GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hi.
This is a bit of a combo question:
I recently got the nRF52 10040 and I'm trying out the included examples on uVision5.
I only managed some examples to...
I am working on BLE Applications, I have tested with different devices like Nexus, Moto, Samsung, LG(ble V 4.0). I am getting the GATT Error 133 in Samsung Devices alone(Samsung...
Hello Nordic,
My goal is to control a small device with NRF51422 without any other additional controller. So I’ve developed my own PCB and I’ve used the example ble_app_uart_s130_pca10028...
Hello Nordic,
My goal is to control a small device with NRF51422 without any other additional controller. So I’ve developed my own PCB and I’ve used the example ble_app_uart_s130_pca10028...
Hi,
I have an nRF52 chip that has likely exceeded the flash endurance limit.
I am observing that after an ERASEALL, not all bits are erased, but after retrying ERASEALL...
Hi, does somebody know why in Segger embedded studio program goes to ses_nrf51_startup.s line 35 ISR_HANDLER NMI_Handler and sits there. I'm trying ble_app_cscs_pca10028_s130...
I only have Bluetooth 4.0 scanners and I bought nrf51 dk with 51422 device (10028) that seems to work as 4.1 Bluetooth. I tried sdk12 s130 and sdk8 s110 beacon examples my...
Hi,
I'm trying to program the bootloader together with an application+SD132 3.0 on the nrf52, but my device gets stuck with the bootloader when I finish programming it...
Hello, I used s130, nRF5_SDK_12.1.0_0d23e2a, SoftDevice 8_9_0.
Is there any example to study the central bond?
I use the examples->ble_central->ble_app_uart_c, the following...
Hi All,
I have hardware setup which has four or more beacons in peripheral mode at particular radius ( approx 10 m) and have a beacon in central mode.
The central beacon...
I'm using the Nordic as a BLE solution, and it is just passing along data through the UART to another chip through the UART. However, I'm not sure how to just pass the data...
Greetings,
I am using pynrfjprog (9.0.0) to write a HEX file to an nRF52 device on the nRF52 DK. I am wondering if there is an easy way to verify the write using API.py...
We're looking to implement buttonless DFUs with the NRF52 and are a bit confused how to send 0x01 to the control point of the service. Is this a control point that is already...
I have tried to export a very simple mbed program (blinks LED1 and LED2 and writes to Serial (USBTX, USBRX)) with no success. I am running on an Ubuntu 32 bit distro. This...
