Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
I am new with nrf52 DK . I was trying to work with SPI code example given in the nordic example folder but its not working . I am trying to transfer the accellero/ gyro data...
I am using SDK 15.0 with the Nordic NRF52840 development board. I wrote my own custom bootloader using CDC ACM as the transport. I am using app_usbd_cdc_acm_read_any to read...
Hello All,
Is there any already available example of OLED display interfacing with nRF52DK, pca10040, SDK 14.1 in Segger Embedded studio?
I am working on a project...
Hi，
I want to measure the time of two signals to calculate the speed and sent the data with BLE. I find the SD effect the GPIOTE_interrupt sometimes, when I try to use GPIOTE...
I an trying to locate and download some programming examples. For instance the BLE Blinky application
ble_app_blinky_c says it is in the EXAMPLE FOLDER, no matter where...
Our project uses nRF52832, and the bluetooth connection has two modes as follows:
one is low-power standby mode connection interval=1000ms;
One is data transmission mode...
We have recently ported our application from SDK 12.2 to SDK 14.2. The application is very power sensitive and uses a high connection interval and slave latency to minimise...
We have a project running based on the SDK 14.1 on a nRF52DK with S132 5.0. The used bootloader works as expected and also an update of the bootloader works properly.
After...
Developing medical sensors for medical institutions according to legislation ( us-fcc.app.box.com/.../8acz9o1cah6eqqpm2q3ktvfkkqt37v7p) in the 2340-2400 MHz band - nrf52 seems...
Dear Sir,
I want to access two slaves viz. MAX30205 & LIS3DH by using nrf52832. The problem is, as per the datasheet the values of the pull up resistors required by both...
Cannot get nRF Sniffer version 2 (beta) to work properly with nRF52 DK running the sniffer_pca10040_51296aa.hex:
Windows 7 64-bit
nRF Sniffer 2.0.0-1.beta
Wireshark...
Hi All,
We are currently in the process of FCC certification for one of our product that uses nRF51822. Our testing house said the the test has failed because of not qualifying...
With a NRF51802 based product, we see DFU errors on Android devices in the field. Our config is: - nrf51802 with s130_nrf51_2.0.1_softdevice and nRF5_SDK_11.0.0_89a8197. ...
