[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
Hi nrf51 developers,
I'm developing multiprotocol application by combining BLE and a proprietary protocol. I'm using concurrent multiprotocol timeslots API. Started with...
I am new to programming both the nRF518122 as well as the Cortex-m0. As I have been building and running the example apps that come with the nrf51 sdk, I run across the CMSIS...
Hello,
I'm developing device application where I need:
peripheral (advertising also when in connection)
central role
whitelisted connections
maybe some encryption...
Hello,
I'm trying to do some simple printfs to hyerperterminal as a way to debug my code. I have used the uart example init code but nothing prints:
void init_uart(void...
I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
I have a nRF51DK. The Softdevice on the board is S110.
I load the ble_app_template from the SDK 8.1 on the chip. It builds with success. Now with the MCP I am able to see...
I'm now using the lastest SDK 8.1.
I found that if I call app_button_enable() after app_button_disable(), app_button_enable() would not function again.
But if I changed...
Hi all,
I read that the nRF51822 comes as a blank chip from the factory, and this means that we have to program the SoftDevice ourself. I am wondering if this is the only...
Hi,
I'm using the Rigado BMD-200 Eval Board with sdk 8.1 and am running the ble_peripheral example titled ble_app_uart. I am using my iphone and the nRF UART app to communicate...
If using the button handling library the #define GPIOTE_CONFIG_NUM_LOW_POWER_EVENTS needs to be changed to add number of buttons being handled.
This wasn't clear to me...
Hi,all. i want to set tx power use interface "ble_tps_tx_power_level_set",and read back tx power level used tps servoce on my phone.how to do that ?Thanks for your reply!
Int the website:
link text
FEATURES show the nordice nRF51822 has 3 data rates (2Mbps/1Mbps/250kbps).
But , I set
number of packets transmitted per connection...
Hi,
If I want to run a blocked task e.g. write 1MB data to the external flash size 8MB(NVRAM), that it takes 3 seconds. What is the best way to to in NRF 51822?
Do you...
Hi,
I'm using the softdevice s110.
The power consumption is sometimes a little weird (around 1 mA). I think that the chip is in debug mode.
How can I know if the chip...
