SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
I tried writing read and write code for sEMMC based on information obtained from an AI assistant. The resulting code is shown below:
As you can see, the block address...
I used an oscilloscope to check the waveform and found that only the clock and IO0 had waveforms. I am using this interface to send data:
nrfx_err_t nrfx_qspi_write (...
This is just simple feedback on the nRF Connect Toolchain Manager v0.9.2.
The download speeds when installing an SDK are terribly slow. On a 1Gb /s connection my PC was...
Hi Nordic team,
We are currently migrating our project from nRF Connect SDK v3.1.1 to v3.2.4 on the nRF9160 .
Our application was working without issues on v3.1.1. After...
I am working with:
NCS Version: 2.6.1 (SoftDevice Controller)
Hardware: nRF52x Platform
on a custom board (nRF52 series) and I'm trying to achieve a "Headphones...
Good morning,
It has been implemented a sleep mode to save battery when the board is not used.
To do that we follow the documentation and implemented the SystemOn mode...
Dear:
I am using SDK12.3 with S132 write application using BLE+DFU+UART+I2C, The device connects and communicates with mobile devices through our own application(ONF Link...
I understand that in %XSYSTEMMODE the flags are not just for fun so practically what are points to do not enable the GNSS always even if I do not use it? I do not care on...
HI
I am currently doing secondary development based on the periodic_adv_conn sample project, using NCS 3.2.1 and the nRF54L15 chip,PHY CODE S8.
I want to add a function...
Hi， We use 52840 based on NCS3.2.4，add UART1 to blinky example because I need to use UART0 to log and UART1 to communicate with MCU for our application. The UART1 could send...
Hello,
I am trying to write data into an external flash memory using a custom board (NRF52840-QFAA). The external flash is the W25Q256JVEIQ. I get a fs_write (-22) error...
As reported on Discord, there is a bug in drivers/serial/uart_nrfx_uarte.c that leads to failing compilation:
zephyr/drivers/serial/uart_nrfx_uarte.c: In function 'cbwt_uarte_async_init...
Hello,
I am following Lesson 9 Exercise 6 of the Dev Academy nRF Connect SDK Intermediate tutorials ( https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate...
SDK:nRF5_SDK_11.0.0_89a8197\examples\ble_peripheral\ble_app_hrs\pca10040\s132_with_dfu\arm4\ble_app_hrs_s132_with_dfu_pca10040
Our product encountered a problem with DFU...
