Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hi,
What is the limitation in terms of the number of bytes that can be sent over the UART to be sent over BLE on the usart ble example? I tried sending 32 bytes and it worked...
Greetings,
I am working with serial mesh (nrfSDk 15.2 for mesh 3.1 with softdevice s132_nrf52_6.1.0) .
1. I followed the serial example available and its working.
2...
Env: nrf52, sdk15, ubuntu, SES
Hi First steps on fstorage. As I just need to store and read an array of some bytes I have chosen fstorage
and I got this as output...
Hi,
I am working on DFU over Mesh for quite a bit now. I did run few tests but never run the DFU on a large network comprising of 100+ nodes. SO, I have questions about...
Hello
We are trying to finalize the layout we need for a nRF9160 module with gps capabilities.
I have downloaded the schematics and layout for the devkit V0.8.5.
what...
my code based on file "nRF5_SDK_14.0.0_3bcc1f7.zip".my hardware based on nrf52832QFAA.
my options set as:
project “bootloader_secure_ble”：
project “ ble_app_hrs ”with...
I changed the bootloader size by changing the flash start address (in the .icf file, from 0xf8000, to 0xf7000). I just want to check what other files/settings needs to be...
I need to use pin 8 and pin 20 as outputs on the nRF52 DK, to be transferred to a custom board built with the nRF52810. I'm using SDK v15.x.x.
I need to drive PWM output...
Im trying to detect power off. The signal power off looks like:
The time to get 0V equal 15seconds. GPIO EVENT and COMP do not see changes in the voltage level, they are...
Hi folks!
I'm working with a couple of nrf52832 on custom boards. I'm trying to implement a procedure for firmware updates. I've already played with the examples from the...
I have found many questions regarding passing bonding information from the application to the bootloader (e.g. https://devzone.nordicsemi.com/f/nordic-q-a/34497/dfu-with-bonds...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image.
I am using "twi_scanner" example code on Development kit. I connected HDC2010...
Errata for nRF52832 Rev 2 version 1.2, errata item 20, RTC: Register values are invalid, has a recommended workaround that i'd like to ensure i've implemented correctly -...
Hello,
I have a project that does what the title states, create a Mesh Network using the Nordic USB Dongles then provision a smartphone using GATT to access the Mesh network...
