if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
Hi,
I have 3 nrf51822 devices. Two of them act as peripheral and one acts as central. Each peripheral is used in a wheel and they are the 2 wheels of a cart. Central is...
We are trying to connect RF51822 with RaspberryPi over Bluetooth. Our aim is to get Light sensor values(lux).
Please advise how to get started with RF1822 Sensor.
*) How...
Hi there~. I tried Nordic's FFT example (SDK 14.2) with a PCA10040 board. So I tried to add that FFT related codes in the heart rate peripheral example. I use the Segger's...
Hello, I am practising and studying the beacon example on nrf52840. While reading the main code, I try to delete the log_init part, however the kit doesn't advertise. I am...
Hello, I hope to realise a scenario that, my kit(nrf52840) advertises certain information, all the mobiles nearby (with BLE) could receive the information. I think the non_connectable...
Hi,
I'm looking for mBed OS 5 examples I can run on the nRF52-DK. At the mBed GitHub, I only found a Blinky and a BLE sample. I'm wondering if you are familiar with more...
I can see that there is one example for UART and it uses application uart module (APP_UART_FIFO_INIT ...). I used this module for printing strings on terminal window, but...
Hello,
I have been working with a nrf52DK PCA10040 V1.2.1 on SDK 14 without a softdevice and I have encountered a problem with a TWI sensor.
I have a TE MEAS MS5611...
Hello,
my usecase is the following: I'd like to use SoftDevice for BLE Advertising / Scanning - every now and then I'd like to "pause" BLE for a few miliseconds and send...
I download the demo project \nRF51_SDK_8.0.0_5fc2c3a\examples\peripheral\uart\uart.uvmpw to my nRF51-DK board, but uart didn't work,all 4 LEDs are on. Is there any mistake...
Finally, I managed to compile ble_beacon in segger.
However, here's what I can not understand.
Using either Segger -> Target -> Download File
or RKNRFGO I managed to...
I got beacon which use nRF51822.
I need to get radiated pattern diagram as attached picture.
this is to get KC certificate.
How can I get information? beacon maker...
Hello,
I'm using a module based on the nRF52810, the Fanstel BT832A. I'm running the basic "ble_app_beacon" firmware from the "nRF5_SDK_14.2.0_17b948a" SDK with a few changes...
I spent a few hours trying to change the base UUID and handles of the attributes of the Blinky peripheral app, just the one service and the button and LED characteristics...
I have couple of nRF51422 boards, nRF5-SDK-for-Mesh (v. 1.0.0) and good will to demonstrate some simple multihop mesh.
And I want to write some data to the flash, but operating...
