Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
I have recently purchased a nrf7002 EK from element14.
I have connected it to nrf5340DK board and tried flashing the Wifi-shell sample application(with the help of video...
I’m not sure if I’m posting in the right forum, but since the EVK-ANNA-B402 uses the nRF52833, I thought this might be the place for questions related to it.
Steps followed...
I am using the cdc_acm example and have added a command to set and read tx power. I am trying to use the following commands for this.
BT_HCI_OP_VS_WRITE_TX_POWER_LEVEL...
Hi,
while using the SoftDevice with MPSL on NCS/Zephyr (nRF52840), there will be a HardFault triggered without using Monitor Mode when a breakpoint is hit.
I understand...
Hi Nordic,
I have installed nRF Connect for desktop for using with nRF5340 Board . After completing the installation I'm getting the following Error.
I have reinstalled...
Features
nRF52840
nRF52832
System current consumption DC/DC at 3 V
0.5μA at 3V System OFF mode,
no RAM retention
1.5μA System ON mode, no RAM retention...
Hi
I'm running the blinky sample (modified) on a custom board based on nrf9160. When compiling with SDK2.3 and toolchain 2.3 the current consumption is about 84uA (LED off...
Hi,
I use VS code (windows 10) to program nRF9160DK under modem mfw_nrf9160_1.3.6, application Asset Tracker V2, JITP certificate generated by nRF Cloud and good SIM card...
What is the power consumption to check battery level?
How quickly at boot time is an accurate battery state of charge available?
What is the RDSon in the path from VBUS...
Hi,
I need to read the registers of the KTD2026 IC as specified in the datasheet.
In short I have to send a read command with the device address (0x30), the address...
Hi, I'm working on a BLE peripheral project using nRF52840 with nRF5SDK version 17.0.2 and softdevice S140 version 7.2.0
We are considering to increase our full device name...
We are starting a new design that requires a LTE-M chip. Upon comparing features between nRF9160 and nRF9161, I see 2 differences
DECT NR+
3GPP Release 14
First...
Hi,
I am reading through different Nordic documentation. In some documentation, it shows a first stage B0 Nordic bootloader. This bootloader then can point to MCUboot...
HI,
I have a product which scan for RFID card through NFC and Mobile Device through BLE after nRF52840 MCU was wakeup.
If I scan NFC and BLE scanning separately, everything...
