SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
Dear All,
I am trying to compile and run the ncs/zephyr/samples/drivers on the nrf9160_pca10090ns. For this reason, I have copy-pasted the file under the ncs/nrf/samples...
Sorry, I want to ask that if I can send Decimal(like accel x,gyro x) by the ble characteristic to the nrfConnect, when I send the information, it always becomes hexadecim...
Dear community members
I have end nodes with nrf52832 (Soft device s132) that can communicate to a central nrf52832 DK in Connection mode based on ble app uart and multiple...
hello, I'm develop use nRF52 SDK15.3 template to measure water press, and gyro value.
but in nrftoolbox app just show signed value, so i want to show signed value.
please...
Hello ,every one ,I found that the nrf Connect will disconnect it self after connecting to the device after 30 seconds, I'm using the sdk15.3.0 ble_app_template example,I...
NRF5_SDK_15.2.0
I am run my android code on android 9 and android 7. Unfortunately my android 9 is paired sometimes and not paired sometimes. especial after i tried to connect...
I am currently developing applications using nRFtoolbox. In case of ses, we are developing a template, but the application does not produce a negative value. In this case...
Hi, this is my first time using nRF52832 as a central device. (S132 6.0.0)
I set up the scan timeout parameters, it does stop scanning at the time I expect,
but strangely...
Hi,
It seems I'm running into the fairly common "solution load command failed (1)" error on a nRF42840DK board.
The console output in Segger gives me the following:
...
Hi, I am using mesh sdk 3.20 and nrf52840.
I am using 3 nodes for testing. One generic on off client and two generic on off servers.
I believe that I have managed to get...
Hello, I am working on a project where I have 2 nRF52832 boards with the PCA10040. I have the example developer code examples. I am using the central and peripheral code examples...
Was looking through the reference designs you have in github .
I figured the difference between nRF52840_qiaa_var1 (what is qiaa ?) and nRF52840_qiaa_var2 is the use of...
Hello everyone,
I am facing an issue with UART communication from my nRF52832 to my GPS module.
I precise that communication in the other way works very well (I get...
We have a need to invert the TTL logic for the serial interface. All our "Unique" SWI serial interfaces use an inverted logic e.g. idle state 0 instead of idle state 1.
...
