I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi,
I am developing a project using the nRF52840 DONGLE. As part of the process, I need to be able to debug my code, so I am using IAR and a J-TRACE PRO for that. The...
I am using NSDK 15.3, MeshSDK 3.2.0, SoftDevice 6.1.1 and nRF52840 DKs.
I successfully integrated the DFU capabilities in my firmware that uses BT Mesh. I am downloading...
I'm studying nRF52811 manual, there are moments not clear to me:
1. Is I/Q sampling paused during SWITCHING slots? For example, if I configure 16 1-msec slots (8 switching...
Hello again Nordic Pros,
I am trying to get some debug logging going using the 52DK running ble uart central under SDK 12.3 and RTT Viewer v6.4.
I have setup config.h...
Hello, I do connection between one nRF52840 (central / NUS) to multiples nRF52840 (peripheral NUS)
in my function static void on_adv_report(nrf_ble_scan_t const * const...
Hi Nordic Developers,
I would like to extend my question on creating vendor specific model from this question I posted earlier (extension of Thingy Mesh Demo v0.1):
https...
Hello Nordic Pros,
Doing some debugging using RTT Viewer and an nRF51822 under SDK12.3. Here is the code lines of interest:
And here are the log messages:
iDrink:...
Good afternoon!
We're considering an off-the-shelf nRF52832 based device for our needs.
the application will likely involve two nRF5283-based devices fitted with external...
Dear All,
On the http_application_update after the download is complete, in order to run the new firmware the user needs to press the reset button.
I would like to be...
As in another post , I was looking for a way to change the TTL per message. Is there a reason that it can only be changed per model? I can imagine the TTL being part of the...
Hello,
I'm trying to use the mesh DFU on 2 nRF52840 DK by following the quick start guide and it didn't work.
Using the mesh sdk 2.0.1 I made the below batch file as described...
Hi,
We need a BLE chip which can be used as a radio which supports BLE SIG mesh and work on standard HCI commands.
Kindly suggest the right device.
Thanks & Regards...
I am using a Mac with SES installed. I created a DFU example and downloaded it to the Thingy 52 to see how it works. That all went fine. Unfortunately, it has disabled the...
Hi all, I'm trying to evaluate nRF Connect SDK, starting with guide in nRF Getting Started Assistant app. So far I've executed every step, but when I try to open the project...
