[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
ble_db_discovery_start () returns NRF_ERROR_INVALID_PARAM (0x7)
This problem occurs when two peripherals are connected to one central unit. The two peripherals use the same...
Hey,
I am having trouble validating this idea through research. I was hoping someone could give me some ballpark feedback.
The setup:
- 15 NRF52832 devices on custom...
all set. while in linking stage i am getting
.\_build\nrf52832_xxaa.axf: Error: L6218E: Undefined symbol nrf_sdh_is_enabled (referred from nrf_fstorage_sd.o). .\_build\nrf52832_xxaa...
Hi,
I am using NRF51422 dk board in our project.We are using SDK 12.3 version , soft device S130 and keil u vision. Here the problem is I am not able to connect the bluetooth...
Hello:
I am able to debug and output to the J-link RTT Viewer(V6.44e) and when I stop debugging or sometimes randmley, the Viewer will display the message
"Warring:...
We're using SAADC to monitor two different voltage rails in different combinations (sometimes one and sometimes both).
I'm experiencing an issue in the following scenario...
Hi
I followed below tutorial, and I tried to send scan response data
https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/ble-advertising...
Hi, everyone,
We are developing projects with nRF52832/51822 chips by using development board PCA10040. The programming of the chips is done by “nRF Connect\Programmer”...
Hi,
I have a problem with the app timer firing incorrectly.
I am using development board nrf52840-DK, Segger Studio 4.22, SDK 15.3.0_59.
When there has gone more than...
Hi
I'm really new to this filed and don't know anything about antenna, please forget me if the question is stupid.
I have an nRF52 DK, I noticed the Bluetooth antenna...
Hello, guys!
Here are the details about my development environment:
SDK = 15.3.0
IDE = SES
SoC = nRF52840-based BL654 module.
In my design, I need to drive a buzzer...
It's cool to have a build_all.sh script that supports so many cross-compilers. I've one more small request.
If run from a tool like CMake, the make tool does not pick...
Hello Nordic team
I am working on nRF52840 DK, SDK v-15.2, I am implementing directed advertising support and other side nRF52830 can capture this directed advertising data...
I'm trying to follow the instructions to install the nRF sniffer 2.0.0.
It appears that the .zip file (nrfsnifferforbluetoothle200c87e17d.zip) is missing the Profile_nRF_Sniffer_v2_001...
