Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
Hi,
I'm developing some projects with the nRF51822 chip and I am not able to debug them successfully any more. However, I have previously debugged correctly some projects...
Hi all,
from the following webpage, I found the there are3 module will support long range , 52811 ,52833 52840, I wanted to confirm that the long range support in 52811...
Tried connecting a J-Link Lite to the debug port of the Thingy:91, get an error message
ERROR: Low voltage detected at the target. Please make sure the device is
ERROR...
Hi,
After a recent windows update I found that when Segger Embedded Studio starts it gives a pop-up No commercial-use license detected. Solution compiles ok. Can this cause...
Hi, I try to update a nRF52832 with SDK 14.2.0 to SDK 15.3. I created a package with SD + BL + APP with the following command:
I'm using nrfutil (v5.1.0) to download the...
Hi,
We are trying to power optimise our device but in the sleep/powerdown mode we seem to be using much more power than expected.
I am seeing consumption of approx 330uA...
I have a question regarding Direction Finding on nRF52833. I cant see any examples related to this in new SDK 16, also I cant see any antenna array recommendation. Do you...
When building a project I get a number of undefined symbols:
.\_build\nrf52840_xxaa.axf: Error: L6218E: Undefined symbol __start_fs_data (referred from nrf_fstorage.o)....
Hi,
I am planning to design a custom board using nrf52840 Soc which receive analog signal from sensor and send ADC outputs through UART to smartphones using Bluetooth communication...
Hi, Everyone
I use sdk15.2 & nrf52832
I am doing a test to read the slave address in TWI
There is one slave device on the board and the slave address is 0x68
I used three...
I am working with SPIS example ( sdk version 15.3). SPI master send data regulaly. For example, it sent 5ms cs low, but there are only two bytes transferred, the first byte...
Hi,
I'm working on a project that is using the the freeRTOS and I want to use the NFC pins P0.9 P0.10 to drive SOFTWARE SERIAL UART with a timer like TIMER1, when I try...
iPhone 8 Plus with nRF connect App[iOS], does not shows BLE 5 beacon in scanning, it only scanning BLE 4 beacons, In Spec of phone it shows it support BLE 5
nRF connect...
Hello,
I follow the nRF Connect SDK on a Windows 10 x64 computer and it's a crap. I get a lot of errors like this one. It's so crappy that I doubt that I will continue with...
Hello,
I am not able to send a command from the BLE (52810) to a DSP over UART which are on my custom board. I have modified a program that uses UART for logging purpose...
