Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Hello, I am having trouble with output display on my nrf52840dk.
I tried resetting the device. It has no effect. I using RIOT OS to flash the board. PyTerm outputs nothing...
Hello, I've been evaluating the PDM hardware driver for the nRF52832, and the PCM output of Thingy. I've found that, for certain impulses at the input of the microphone, the...
Hi I have successfully set up my ARM SPI interface to use the nRF24 chip. At this time I'm trying to establish connection but I'm not sure I under stand the setup for comm...
I'm getting this when im trying to select the device.
when i try to update the firmware nrfgo studio is getting closed
please help me in solving this!!
Let's first compare two pieces code:
This one works:
But this one doesn't:
My problem is that as soon as I try to process received data, some of data is lost. Is...
I am developing with SDK 15.0.0
I want to add NUS service in ble_app_buttonless_dfu example.
All I have done:
1. Add including files and including paths to the project...
This is really a two part question.
1. How do I even refer to pin P1.00? It's clear that pin P0.06 is referred to simply as pin 6, but what is the naming convention for...
Hi,
i try without succes to go into MemoryRentention Timer On sleep mode, and wakeup with the analog comparator activated by AIN1 without sucess. Here is my code, please...
Hello I am using nrf52832. I would like to write a custom ISR for GPIO based interrupt. Are there any examples/documentation i could use to get started on this.?
Dear All,
we use Reference configuration 4 and have connected the DK to our custom PCB. 3.3V of the DK go into VDDH and otherwise only GND and SWDIO/SWCLK are connected...
hi
i downloaded nordic thingy52 FW and i uploaded on my board PCA20020
and that is working correctly but when a i downloaded nRF5_SDK_15.0.0 at first i compile (ble_app_beacon...
Dear Nordic,
i am just testing ble examples in nrf 52840 dongle and also implementing one uart for just testing
TX pin - 1.10
RX pin - 1.13
transmission works fine...
Hi,
I'm referring to -
1. Custom HID over GATT device
2. nRF51422 HID example modification
So for now, I just used the descriptor mentioned in above links. But "hello...
Hello,
The softdevice S132_SDS_v4.1 spécification write that supports 20 connections at the same time.
I would like to know if it's possible to have 1 central and 20 peripherals...
I'm attempting to make cli application to load from after the softdevice and based on a command enable/disable the BLE functionality. Is there any simple way to do this? Are...
