SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
I'm building the ble_hrs_app for my pca10000, I've made a couple of changes (to change the LEDS which show) and I'm building it with CrossWorks .. which I thought I knew how...
Hello, I'm trying to get my nrf51822 project from SDK 5.0.0 running in the latest SDK 5.2.0. To minimize problems with KEIL I used the template project and copied my sources...
Hello,
I have a nRF51822 Evaluation Kit, and a working ble_app_uart demo software.
I would like use the Fujitsu MBH7BLZ02-109004 module . I can flash and verify the softdevice...
I am using the following code to manage a buffer to put through data to the ble stack. I think I saw a similar code on the nRFready Desktop 2 v1.0.4 examples:
/**@brief...
Are there any pin restrictions for connecting the PWM module to? That is, would I be able to output the a PWM signal (created by the internal PWM facility) through any P0...
Hello Gentlemen,
I'm developing an Android App that needs to connect to nRF. The nRF sensor does not have keyboard, display or buttom.
But we can have OOB which is a...
Hello!
I have two question from Heart Rate Application.
What BLE_L2CAP_MTU_DEF number presents?
I do not see event handlers for WAKEUP_BUTTON and BONDMNGR_DELETE_BUTTON...
Development Board can not be loaded by Keil 4.7.2
nRF51 by Nordic can not be identified by Keil automatically, how to configure the parameter for programming?
The Android API Kitkat documentation says the following about BluetoothSockect.connect()
"This method will block until a connection is made or the connection fails. If...
Hello Gentlemen,
I'm looking for sample code that shows how to enable security which prompts for a PIN number on the Android device when I want to connect to the nRF. ...
On the box for the nRF51822 there's one tiny sticker with nRF6815, Rev 2.2.0, 2014.15 and 10004490 written on it.
I can't find ohter information on the box.
Hi ,
i would like to know about
1)how to enable softdevice in nrf51288?
2) how to check softdevice is enabled or not?
can any one share information related to it...
nrf51_sdk_v5_2_0_39364\nrf51822\Board\pca10001\s110\experimental\ble_app_uart
runs ok when connected to Android 4.4 Nesus7 II
but will return error code 8 when connect...
