Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Hi Devzone!
I'm using uart to send AT commands to LTE modem.
but when I send AT commands the response is quite strange, and I think the command is sent twice. I don...
Hi, I'm using the Zigbee SDKv3.1.0 Cli agent as coordinator, the Zigbee SDKv3.1.0 Ligh_Switch example and two commercial light bulb (Ikea and Heiman) I'm be able to command...
Hi,
TWI init using nrf_drv_twi_init, if event_handler is null it will be blocking mode. My question is, which one is less power consuming? block or non-blocking mode?...
Hi Everyone
*ITS VERY URGENT ISSUE*.
I am using nrf52840 PDK with segger embedded IDE.
I was trying to use the QSPI module to write data to the external flash memory...
Hello All,
I am trying to send data on serial port of nrf9160 to be published on a topic using MQTT protocol. So far using the mqtt example and UART example, I have successfully...
Hi,
We are using nRF52840 DK with PPK stacked on top of it. We flashed BLE power profiling application, connectable advertising and observing graph on PPK.
Please answer...
Hello
I simply wanted to build an executable from a customized nrfutil. Ran the "pyinstaller nrfutil.spec" and afterwards started the nrfutil.exe from command line. This...
Hi , i want to use SDK 16 with BDS template, is there plugin for ? Or its posssibly to use http://developer.nordicsemi.com/nRF51_bluetooth_development_studio_plugin/ with...
Is this a bug that is resolved in a particular softdevice version? If not, is there more information somewhere on this bug? How do i ensure that my code is robust against...
Are there examples of HW and SW to allow Power Amp, LNA, and TX/RX switch to be connected to the nRF52840_DK?
Or can you tell me what PIN on the chip or connector and pin...
Hello -
We are developing some low power code on the nRF52840-DK, using SDK 15.3.0 on FreeRTOS. I noticed that in the port_cmsys_systick.c file, in the vPortSuppressTicksAndSleep...
I am building a prototype that will use the nrf52840, with limited space. Would making a small pcb antenna or using a chip antenna be better and what is the setup needed for...
Hi,
I would like to measure the voltage generated by a Thermoelectric generator. The voltage vary between -250mV and 250mV depending on the temperature gradient.
If...
I'm looking for alternative xtal's (mhz + rtc) for use on boards where space is very limited.
Silego's GreenCLK3 looks like a great option, though that one is right now...
