I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I couldn't use nRF Connect (BLE) under Linux, after updating the FW, it tries to open /dev/ttyACM0 but fails to do so.
Not a "permission" problem: the user is in uucp...
Hi,
I'm unable to compile the OpenMesh example application. I've modified the make file with correct paths. However I'm getting the following error. Can you please help...
I have a NRF51 talking through the UART to another uC, and I'm trying to log messages through Segger RTT. Everything works normally until I start to send some data through...
If SEGGER_RTT_CONFIG_DEFAULT_MODE is "BLOCK", the program won't start without RTT attached - at least for me... is there a possible solution?
I mean, technically it makes...
hello ,everyone
I was confused by a PWM problem for a long time , on nrf52832 SDK13 ,i wanna change the PWM duty cycle every period ,but now i find can not change it at...
Hey dear Devzone,
I am trying out some Thread and BLE dynamical examples on my nRF52840's but running into some problems using the " ble_thread_dyn_mtd_coap_cli " example...
Hello nordic dev community,
I am completely new to nordic products. I attended one of the conference and got more information regarding developer zone and info center....
Hi,
I am wondering why the ccm library uses the software aes encryption. Is there anything wrong with the hardware encryption so that it should not be used?
Marius
Hi there,
hope you are doing fine.
I am using SDK 14.1 with SoftDevice 132 as well as a state machine framework which needs a have a function called periodically to...
Hi. I'm using nRF52832, SDK13.0.0 as peripheral.
When I want to disconnect central, I'm using sd_ble_gap_disconnect function as below.
err_code = sd_ble_gap_disconnect...
When I try to build and run any example from the nRF5 SDK, it can compile successfully. But when loading to the eval kit, it can't find the 's140_nrf52840_5.0.0-2_alpha_softdevice...
Hello Everyone,
I am using nrf51822 256Kb Flash and 32KB RAM Raytac's BLE module with SDK11, S130 with over the air Bootloader (16Kb).
So the aim is that when a particular...
Hi all,
I encountered a problem , when I connect 1 board central to 2 board peripheral via NUS . It connected and discovery success . But at
static void db_disc_handler...
I was compiling a project(ble_app_uart and I am using PCA10028), it was not successful and KEIL5 display this:
it looks like I didn't install NordicSemiconductor.nRF_DeviceFamilyPack...
