SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
Hi,
i have a wierd behavior on my board.
On my nrf52832 custom board i have sdk14.1 with DEBUG flag and NRF_LOG enabled.
Usualy when my board crash i got into some kind...
Hi.
I have RF communication between nRF24L01 + and nRF24LU1 +.
Incorrect data is transmitted occasionally during communication.
So, I want to use CRC, but when CRC...
I want to get 32000 bytes per second with NRF24LU1+ ,as my audio sampling rate is 16K and sampling bits is 16.But actually I have lost one packet or more per 10ms. data loss...
Hi Everyone,
Is it possible to programmatically assign a static mesh-local EID IPv6 address to a node in a network? I would like to communicate to individual nodes in the...
I am using the nRF52832 Soc, and have a requirement of using a timer with a large timeout value, hence I want to use the watchdog timer.But as I get TIMEOUT interrupt the...
Hello!
I need sensitive gpio.
I want that is gpio rising in 20[nsec].
However, the test results using the function below show that the gpio rise time is 200 nsec...
Hi,
I am new to the BLE environment. I am trying to connect my smart phone with nRF52832 development kit over BLE. Here, my smart phone should be able to send some user...
I am looking to extend the RTC beyond 24 bits using the Overflow interrupt.
The code in the rtc handler would look like:
static void rtc_handler(nrf_drv_rtc_int_type_t...
I have been trying to install the new version of everything Nordic 52.
That starts with the MDK 5.18.
To make sure I don't have an update problem I do a clean install...
Hi,
I want to know about mathematical formula to find / estimate the battery life of Bluetooth beacon containing NRF8240. If chip is transmitting at +8 dBm and have 1000...
Hi,
I add the NUS in the ble_app_hids_mouse example which the sdk version is 14.0.
There are four services in the project: dis, bas, hids and nus.
When I connceted the...
hi all ,
I am looking out theory about SM layer in BLE . I read CoreV5.0 but I do not understand much about pairing , bonding , STK , LTK . Can you give me some document...
Can the link between two devices communicating with each other via NRF24L01+ be improved by using Tx messages with no ack (W_TX_PAYLOAD_NO_ACK) instead of messages with ack...
Specifically, sinking a Cree C503B green LED (Vf 3.2V at 20ma) from a GPIO configured for high drive, without a current limiting resistor, from VDD 3.6V?
Figure 23 “GPIO...
