Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Hi,
I am using nrf51822 with s110 softdevice version 8.0.
Is there any way i can know the state of my radio at some point in the code execution?
In short I want to access...
As explained by electronut in his Blog and Lijun here , it is possible to program an External nRF51822 board using the SWD interface of the nRF51-DK.
But what about a custom...
I have a project, and nRF52832 it 's good chip for me, because it has NFC/ bluetooth communication.
I would like to know if nRF52832 can pilot epaper display. nRF52832 does...
Hi,all. i face a problem. the office DFU flowchart is device reset--->bootloader --->upload firmware to device ---->device reset.i want to implement as follow: upload firmware...
Dear all
We did nordic beacon board in that we not able to flash the device
We are checked core voltage 1.2V and 1.7V are coming .But i want to confirm external CLOCK will...
Hi,
I want to change the interval time of 51822 dongle with the instruction here devzone.nordicsemi.com/.../
The default value is 100ms as following
#define NON_CONNECTABLE_ADV_INTERVAL...
Hey guys,
I’m working on an nRF51822 design where I’d like to check the value of a GPIO at Power-ON, then either shutdown, OR start the BLE stack and do BLE stuff. I really...
when compiling " ble_app_proximity " exampled by Nordic, it indicates errors:
" D:\Program Files\MDK5\ARM\PACK\NordicSemiconductor\nRF_Drivers\3.0.0\gpiote\nrf_drv_gpiote...
Hi:
in ble_app_proximity(SDK5.2) ,i use lightblue to write data to ble,and i set a breakpoint in "ble_evt_dispatch".but i found breakpoint can't work when i send data to...
My product have to pass SRRC certification. The certification lab need 3 prototype. Their bt RF frequency must work at 2402MHz, 2441MHz and 2480MHz separately.
How can I...
Hi ,
I am unable to write to discover all services and write to a characteristic too.
On discovering services:
Discovering primary services
Received service discovery...
One of our computing-intensive algorithm takes actually ca 1.9s to finish. And it will be run periodically. Is there a way to minimize the power consumption of CPU processing...
class BatteryService {
public:
/**
* @param[ref] _ble
* BLE object for the underlying controller.
* @param[in] level
* 8bit batterly level. Usually used to represent...
I am looking through the following mBed development platforms. I am looking to integrate some mbed code into a production design. I am looking at which platform to export...
Hello Folks,
I want to send an array of two bytes and read six bytes back . Even though I am using bellow function but the Oscilloscope shows only 4 bytes of clock cycles...
