Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
We have a Nordic 52840 based product which today we support with a custom gateway hardware. Now we want to write mobile apps (Android and IOS) to talk to this directly.
...
I have an NRF9160 system running and I see mention of " The nRF9160 PWM peripheral can capture the period and pulse width of an external PWM signal" but was a little confused...
DeviceTree Visual Editor shows SPI1 as enabled, but the changes are not reflected properly in the GUI or in build behavior.
I receive the following build error : " DT_N_S_soc_S_gpio_50000000...
The nPM2100 datasheet (v1.0) provides Figure 8: Load current triggering mode change vs. VOUT.
Can you confirm:
1. Consider the system is in Low Power mode. If the load...
Hello,
I am trying to implement OTA through BLE, and as Im building the program, Im getting a build error as :
error: 'FLASH_DEVICE_BASE' undeclared (first use in this...
Hello. I have a light sensor connected to 2 gpio pins on nrf5340, Enable Pin : P0.08 and Output Pin: P0.07 Trying to trigger an interrupt based on the light. With the button...
hi support team,
docs says we can program 54l15 external spi flash ,please refer to : https://docs.nordicsemi.com/bundle/nrfutil/page/nrfutil-device/guides/programming_external_memory...
Hi,the Nordic team I'm working on low-power devices that Matter over threads by nrf54l15,I found a problem at present. I interrupted the configuration of the two PIR input...
Hi all,
I’m working on an nRF5340 project where the network core runs a hci_ipc firmware to forward HCI RAW packets to the application core, which then parses vendor-specific...
Hello DevZone!
All samples with Application Event Manager (CAF, nRF Desktop) has simple main function like that:
Main thread has terminated after executing and main...
Dear reader,
I am currently working on a project involving the NRF54L15 microcontroller. In the specifications of the MCU, under Circuit Configuration 1 for QFN48 (QFAA...
Hi I’m looking for some advice on what may be drawing power from the thingy 91x.
I have measured the power consumption of the nrf91 the nRF 5340 and the nRF 7002 using the...
I want to use P0.13 for ADC reading. However, I noticed that it is already used as an SCK pin in this configuration:
spi3_default: spi3_default { group1 { psels = <NRF_PSEL...
Hi!
I’m currently setting up multi-image DFU on the nRF5340 using external flash.
By following the official documentation and samples, I managed to get it working correctly...
I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
