Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Dear Support Team,
I’m currently experiencing an issue with Segger Embedded Studio where no output is shown in the Debug Terminal. It was working perfectly before, but after...
After connecting to an nRF9160 using SEGGER tools (J-Link RTT Viewer v7.62b), excess power consumption is observed until the device is reset (via `nrfjprog -r`)
First the...
I have a Central using nRF52832. The project is working correctly but I’m having trouble getting FOTA via BLE to function on top of it.
I’m using NCS 3.0.2 (3.1.0 and...
Hello everyone,
I am writing an application with three sensors on the same SPI1 interface on my nRF52840. See the following devicetree section:
For all sensors, I use...
I’m following the nRF54L Series Express Course – Lesson 5: Power Consumption Demo Part 2 sample code, using nRF54L15DK to test the deepsleep → wakeup functionality. However...
I work nRF54L15 with NCS311.
I want to save application's parameters on UICR.OPT[].
But it looks like somewhere in OPT is used by the bootloader.
What parts of UICR...
Hi, i am working on the nrf5280, and I have set up BLE with NUS so I have a shell and logging over BLE, as well as logging over UART. I have a python script running that connects...
Hi,
I'm preparing to run some openthread code on an nRF5340DK using the latest SDK and toolchain v3.1.1. A simple program works fine until I set the CONFIG_OPENTHREAD...
Dear Sir,
I have purchased nRF5340 DK (Will call it device hereafter) and am trying to bring it up.
I have connected the device to Linux but the device was not detectable...
I’m testing the nRF9151 DK in India and trying to use the nRF Connect app (Quick Start guide) to connect the device to the network.
Board: nRF9151 DK
SIM: Onomondo...
I have a nRF52DK board that I loaded the peripheral_uart program in a while ago. I tried to get the board running again but when it calls err = settings_load() it just keeps...
I'm currently trying to integrate Memfault to my project that is using nRF9151 DK. Memfault was working fine until I turned on these configs:
# Collect LTE Metrics CONFIG_MEMFAULT_NCS_LTE_METRICS...
The application here is reading a Manchester stream on a GPIO. which comes from a MAX41473 radio IC.
Decoding is working fine using GPIOTE, timers & PPI to time & decode...
Hi,
I have two nrf9161 dev kits. I have flashed the firmware 2.0.1. Then I flashed the hello_dect example.
Now I always get an error and the program does not start. *...
Hi,
I am able to do some stuff partially using the command
$ west build -b nrf52840dongle_nrf52840 -- -DDTC_OVERLAY_FILE=usb.overlay -DOVERLAY_CONFIG=prj_cdc.conf
With...
