I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
After switching to the BLE advertising module in SDK 16.0.0 (on an nRF52 board) and using it for over 3 months I am now discovering that no matter how I configure the advertising...
My firmware is blocked on custom board until RTT connects: Code hits and blocks on a printf. This doesnt happen when using an NRF5340, but does with NRF5280. Just trying to...
Hello, I am using v3.1.0 of the nRF SDK with a nRF52840-DK board.
I would like to run the "Counter RTC Driver Sample" (nrf/samples/zephyr/drivers/counter/alarm). The README...
I am updating our production tools and starting by simply trying to program the Thingy91 (or DK) with the following example from the internet. I keep getting timeout errors...
Hi Team,
I have configured I2C0 for reading data and sending iqs323 and iqs7211a. i have configured overlay file according pin conjuration which is below.
Pin configuration...
HI
Currently using NRF54L15 with NCS v3.0.0 and the periodic_sync_conn sample. I have created sysbuild.conf and added SB_CONFIG_BOOTLOADER_MCUBOOT=y. After compilation,...
Hi all,
I’m working with an nRF-based board and need to via software disable the internal DC-DC converter and use the LDO exclusively for testing purposes. I’m unclear on...
To confirm, when connecting a power source to VBAT for the first time, nPM2100 will automatically transition to Active mode assuming the power source can deliver enough current...
The error started coming after updating the sdk version from ncs v.2.9 to ncs v3.1
[00:06:58.439,514] <inf> _https: Log:Sock before -1 [00:06:58.484,649] <inf>_https:...
Hello,
Going through DevAcademy SDK Intermediate and it mentions running 'west boards'. Doesn't work for me:
Any ideas ?
Sadly after weeks of little problems like this...
Below is my change, set options to BT_LE_PER_ADV_OPT_USE_TX_POWER
But it always display Failed to set periodic advertising parameters (err -5) , why?
My hardware is...
Hi again,
I'm having trouble with the Matter Test Harness. I have been running tests in isolation one by one and fixing issues the TH finds. Now I have run into an issue...
Hi,
toolchain:-v3.1.0,sdk:v3.1.0. i am using the vscode software for the development
Basically i am trying to connect the peripheral using the address (mac:- 7C:D9:F4...
Hello,
I am using NRF5340-DK for my project and I wanted to know if there is some example on how to read and extract the public key from this type of certificate. I have...
