I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
Hi, This is the second time posting this issue. Using nRF9160 dk with nRF Connect SDK v1.3.1 with zepyhr v2.3.0-rc1-ncs2. I tried the BME280 sample from zephyr which gives...
Hi,
I connect the nRF52820 and other devices with UART and communicate with the baud rate of 38400bps.
I know that the transfer error rate is different for each baud...
I have two tasks and I want to run those tasks one after the other.
currently when I comment on one of the task, the firmware running without any error.
if run those two...
I have been unsuccessful attempting to perform an FDS write or update WITHIN the DFU Event handler... the update or write never completes (no FDS_EVT_WRITE or FDS_EVT_UPDATE...
Hi,
I am using NRF5340DK, and I want to define P0.20 as my SPI MOSI pin.
However, this pin is pre-defined by Zephyr as uart0 tx pin, in zephyr.dts:
Everytime I reset...
Hello,
Our product has two pieces of information that must be programmed during production: a shared secret key (128 bits) and a public, unique device identifier, also 128...
Hi guys:
I flashed the ble_app_uart(SDK-location\nRF5_SDK_15.0.0_a53641a\nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral\ble_app_uart.),
When I pressed button1, there...
Dear all,
I'm trying to modify ble_central_uart (SDK16) to connect two peripherals. I've achieved the connection and been able to print receiving data via UART.
But...
Hi All,
I am NEW to Nordic Devices and I want to try to learn as much as I can.
I have bought a startup Dev Board to learn my skills with: E104-BT5032A-TB E104-BT5032A...
Hi guys.
I wonder the program run start from which section and how to enter the app when 52840 poweron? Start from SofeDevice?
I only flashed ble_app_uart and SoftDevice...
Hi all,
I'm trying to transfer my custom project pca10056 (which is to broadcast a beacon) to nRF52811 hardware and I'm facing some issues in the last stage of build.
...
HI ,
My environment:
nrf connect sdk
nrf5340 dk
segger studio ide.
could you please provide me timer example code for nrf5340 board.
Thanks & Regards,
...
Hi,
I am using an NRF 51422 DK, SDK 12.3, and Soft Device S130. I am also a beginner to development with Nordic Products, and RSSI collection in general. I am using the...
SDK: 17.0.2
IDE: SES
nRF52832 module
Hi!
I have a nRF52832 based custom board operating on battery power. I assigned a variable to the non_init section in SES and...
Hey!
I have an isp1807 test board, which uses an nrf52840 chip, and an isp1p807 programmer (ISP130603E). Currently, my code is written using the nrf52 sdk v17. When I am...
