In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
I am using MeshSDK 4.2.0 and nRF52840.
I have looked into the provisioner example and the provisioner_store function in main.c only seems to store m_nw_state, which only...
Hi all,
I have some issues to print and parse JSON file using cJSON features. My code works without problems in SDK, but when I try the same code in Mesh part, I am not...
Hello, i'm trying to build zephyr\samples\subsys\usb\cdc_acm but i get the following error:
1> zephyr/isr_tables.c does not exist. 1> Combining ‘zephyr/isr_tables.c’ 1>...
With very low data rates and short packets between two nRF52840s which of the following can operate at the lowest power?
1) ble peripheral to ble central uart
2) Enhanced...
Hello Dev
I'm working with MQTT sample on nRF9160 DK device and while that when I called facing some kernel based issue regarding k_sleep() function.
I'm getting this...
Hi,
Thanks for the help. I have run the proximity detection application in nRF52832 nordic thingy. Initially the LED was blinking in the thingy board but when I switched...
Hi,
Though the Thread CLI sample's 'README.rst' lists the following supported optional extensions, it does not specifically describe how to set the specific '.conf' files...
Hi everyone, Lately I have been using a PCA10040 (nRF52-DK) with J-Link OB-SAM3U128-V2-NordicSem V1.00 version. I'm trying to program two boards one with nRF51822_xxAA and...
Hi I am wondering what the best way to go about developing a RPi based system for presence detection with nordic ble devices
I would like to limit the bluetooth signal to...
Hello,
We are looking to do OTA device firmware update by GSM for the nRF52840.
We have a custom board with a nRF52840 and a GSM/LTE-M modem. They are communicating together...
SDK: 14.1.0
CHIP: nRF52840
CONFIG: ZIGBEE&BLE MULTI PROTOCOL
I wants to keep store zigbee pairing data after reset.
I setups like this.
After joining procedure...
From the gnss_extension.rst documentation shown below, it appears as thought the GNSS receiver can retain solution information from previous fixes/tracking in order to speed...
Hello Nordic!
I'm starting to develop my own Zigbee device with the nrf52840DK and I need to send some attributes to my coordinator, initially the door lock status is enough...
I am currently using an external JLINK to program the 9160 module, after adding read protection. Unable to recover using nrfjprog, report the following error:
ERROR: Recover...
