Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
I am a newbie for BLE MESH. Trying to migrate the existing product which based on self-defined GATT service to BLE MESH network, and got confused.
Current scenerio, the...
Hi.
I am using nRF52840 as a USB mass storage device with SD card. I came across the docs stating that the total number of BULK endpoints available are 14 (7 IN, 7 OUT)...
I have a working code to get FatFs running with SD card over SPI0 interface on a nRF52840 DK. I wanted to know if it is possible to add another SD card with FatFs on SPI2...
Hi,
With the S132 SoftDevice running, is there a way I can ask it to temporarily pause interrupts for a small segment of time so that I can execute extremely time critical...
Hi, The DFU process is working correctly and I've tried downgrading the app version which throws the expected error, so it is stored someplace Accessing via the recommended...
Please tell me everyone's knowledge!
I've seen discussions on smartphones that support "LE Coded PHY", but I'm looking for a tablet size.
Is there any smartphone with...
I'm trying to get my nrf9160 DK to communicate with an i2c device so I setup a project to enable the i2c module and use TWIM to send i2c data. But then I run it and it only...
Hi,
I am using nRF52832 S132 SDK15.2
I am developing an application where the development kit which i am programming is a peripheral.
i want this to connect to specific...
Hey All,
I'm running the LTE Link Monitor on nRF Connect 3.3.3. I'm connecting to my custom nR9160 Feather via the built in USB-to-Serial. I'm able to open the serial port...
I tried to drive MAX30003 to get ECG signals through nrf52832.
I use an analog signal instrument to give the standard ECG signals. Now,the nrf's SPI timing sequence is right...
Hello,
The BLE peripheral I'm developing does not have any specific required connection parameters. I understand that the central ultimately controls the selection of parameters...
Dear
I modify the example of PCA10056 mesh light-server for PCA10059 and it works after I program PCA10059 by nRF Connect –programmer go through USB interface. But there...
Hello,
What is the PPM of LFRC?
In our case, the device will remain in low power mode (System ON, wake up from RTC). The device will wake up at every one hour. Which...
Hello Nordic,
nRF52840, SDK16.0, Softdevice 7.0.1.
I'm using LFCLK to generate an accurate tick for device time keeping (with Prescaler=255, Freq=128Hz, Tick=7.8125ms...
Hi all,
I have a problem when I connect the nRF51822 to my phone.
I use the softdevice S130 and the following code attach .
When I use the nRFconnect in my phone, I...
