Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
Please help me !
(spi_maseter_config.h at line 29)
#define SPI_PSELMOSI0 20u /**< SPI Master Out Slave In GPIO pin number. */
nRF51822 QFAA Package pin no.20 = P0.14...
I'd like to use 'Direct Advertising' to get the attention of a Central (a specific one or any in range) when an event happens on the peripheral. Is this mode supported by...
Hi,
I hooked up an nRF8001 (Olimex) to my logic analyzer and am observing the behaviour of the RDYn pin.
After resetting the nRF8001 through the RESET pin, the RDYn...
Hi All,
Just got my NRF51822 development board today and cannot get the heart rate demo from SDK to work. Two issues:
1> The PCA1004 board (the one without antenna)...
Dear Sir, We are intending to develop wireless UART- BLE module for our wearable product (Cable replacement profile). Please, help me to get to know about UUID and cable replacement...
Is sd_ble_uuid_vs_add available over the serialzation interface? How can we add a custom vendor ID over the interface if there isn't a serialzation function for it here ?
Hello,
I have made some current and timing measurements on the nRF51822 Development Kit (connected to a nRFgo Starter Kit) running some of the example applications provided...
I would like to drive an LED from the nrf51822 gpio
How much current can the nrf51822.
How much current can the nrf51822 gpio supply?
Is there a recommended LED for...
Hi. I am using a nRF8002 DK, and i am working with nRFgo Studio for 64 bits, in a windows 7 and windows 8 computers (for testing of the error purposes). I am having serious...
How to set READ property to a characteristic pipe through nRFGO studio.Actually i am not able to set READ property to any pipe.How can i do this?
Because i want iPhone...
Hi:
I use TIMER compare function, I open four channels and every channel produce interrupter.Here are some of my code:
NRF_TIMER1->TASKS_CLEAR = 1;
NRF_TIMER1->CC...
Hi. I've never asked a question here, and I'm a complete beginner to embedded programming, so I apologize if I break protocol in anything I do on here.
My setup:
nrfgo...
HI,all!
I have a question about downloading program into nrf51822 MCU.
That is:
As you konw, using the nRFgoStdio to download the code, you have to download the softdevice...
Hi all,
I have a devicewith display and only want a specific smartphone with my APP to connect to it.
I implement the authentication procedure at application level by...
