Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
Hey,
I'm using nRF as a SPI slave with a Raspberry Pi. I'm seeing that even at ~3MHz SPI frequency, my first byte transferred gets corrupted. I have a test setup where...
I am using nrf52 with s132 and armgcc
As I add functionality to the code I get to a stage where it fails. Linker runs OK but the result fails to execute.
The observable...
I am currently working on a BLE beacon project on nRF51822. Using SDK 12.3.0 and s130. The device has to advertise URL, advertising name and output power level. And these...
I am trying to control a current measurement chip (DDC114) that works with a protocol that is close (enough) to SPI. It has 2 channels, s.t. it can be read out and integrating...
I am attempting to run my first bit of code on my Nordic nRF52-DK and every time I have attempted to upload the code to the board, the board disconnects in the middle of the...
Hi, I'm using nRF52832, SDK13.0.0 as peripheral.
My iPhone app(my company's) makes connection without problem.
But Android app gets connection fail when it tries to connect...
Hi @ all,
We tried to enable debug log for lwIP module by setting NRF_LWIP_DRIVER_CONFIG_LOG_ENABLED in sdk_config.h to 1.
This threw two errors during the build process...
Hi @ all,
by working on a MQTT project using IoT SDK v1.0.0 (SDK v14.1) we discovered problems with TCP packets not being transmitted.
Using lwIP, transmitting TCP packets...
Hi there,
I was able to work with uart ble example described in tutorials/36/.
My question is how to disable encryption on BLE link? Specifically, we need to make disable...
Hi.
I'm testing multiperipheral function,
and have established multiple connections (1 single Peripheral with multiple Centrals).
But it seems that the Peripheral can...
I have no idea what is going on.
I am using IAR 7.8 and as I wrote, it gets reset when it hit the breakpoint.
every variable return to its initial value, and BLE get disconnected...
Hello,
I was wondering whether or not the standard analog pins on the nrf52832 have to be defined as analog inputs with the gpio methods.
I ask this because I am trying...
Hi there, I was able to work with uart ble example described in tutorials/36/.
My question is how to disable encryption on BLE link? Specifically, we need to make disable...
Hello All,
We need the following for reference purpose only
nRF6939-HW
nRFready Smart Remote 3 for nRF52 Series Hardware Files
www.nordicsemi.com/.../nRFready...
Hi,
I am building a custom PCB using the nRF51422 chip. I need to include a pushbutton switch on the PCB to generate an interrupt when it is pressed(gpiote). I am connecting...
