Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
hi
I am using peer manager to pair and bond android phone to nrf52840. I want to give custom peer id to this phone during bonding process, then if i lost this phone i will...
Hello,
I am sending a float in my BLE payload, using nRF Connect I can sniff and see that the value is being sending, it changes every time.
However, in my central when...
Hello Nordic community,
First of all would like to say that I am aware that BLE protocol allows to send only up to 20 bytes size packets. Moreover, I understand that I...
Dear Sir,
I am trying to access max30101 via nrf51422. When I am calling the function it is falling into Hardfault_handler & not getting out of it. I don't know anything...
After already having sent a few notifications with a custom BLE characteristic, I am getting a HardFault in the softdevice.
Initially I had added a log call to print the...
I am trying to upgrade from SDK 13 to SDK 14.2
and get a lot of compilation errors using gcc
Why have SDK path and filenames changed like:
c:/Nordic/components/libraries...
Hello, My question is when the nrf51822 connect the phone A, I whant disconnect ble on nrf51822 side let the new phone B can scan and connect nrf51822.
when used "sd_ble_gap_disconnect...
main (5).c
I have attached my main code here.Please have a look at it.I am using fs_store to write in flash location in the on_adv_report() function under the switch case...
Hello Everyone,
I am using nrf51822 with S130.
After completely erasing the chip, with the below mentioned code snippet in application code:
NRF_NVMC->CONFIG = NVMC_CONFIG_WEN_Wen...
Is there a way to capture and clear a timer without being interrupted. This doesn't seem possible with shortcuts. also it looks like theres no capture event with which to...
Hi,
Im using nrf52 dk of pca10040 of softdevice 132 with sdk version 11. I'm working on MPUexamples. The codes used to work few days back but now, it no longer works properly...
Hi!
I'm developing an application with a dual role on the nRF52840 PDK. On the one hand, the second nRF52840 PDK in the peripheral mode with which it is necessary to provide...
hello
i want to make one way data flow connection by using 2 nrf52832 and keil 5v
TX uart ----->BLE ----->BLE -----> RX uart
can you please help me!!
thank you...
Hello,
I am trying to compile this demo with Segger Embedded Studio but compilation always fail with the error "Cannot open file C:/nRF5_SDK_14.2.0_17b948a/examples/ble_central_and_peripheral...
