Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
I just realized this feature is available from NCS V3.3.0.
Does it support nRF52 series such as nRF52832 with DFU through BLE?
In this page, it seems only nRF54 are included...
Hello,
I'm using nRF9151 as a HCI host and nRF52840 as HCI controller (nRF52840 config is based on HCI lpuart example). Recently I updated NCS to 3.2.2 and I started observing...
Hello, my name is dio.
I created an HCI UART application using nRF Connect for VS Code with NCS v3.2.4 and enabled the Channel Sounding component via the nRF Kconfig GUI...
I am developing a dual-mode HID device (mouse) using nRF54L15 with nRF Connect SDK v3.1.1 . The device determines its mode (BLE_mouse or ESB) at boot time via a GPIO pin ...
Hello,
I have designed a PCB with nRF54L15 SoC. Now the issue is that I have by mistake changed the MISO/MOSI pins of the device. As you can see in the following image....
Hello,
i have a custom board with a nRF52832 on it. TL:DR: i can't seem to get a connection to the chip via the SWD
When i try to recover the device it tells me the debug...
I want to flash an example firmware onto my nrf5340 board. I want to test le coded phy. So whych example should I use from the nrf sdk 2.4.0 to flash onto my device so that...
Hi,
there are several devices with same Firmware/Modem firmware/Hardware. All device were working. While all others continue to work, one suddenly gives me this:
Once...
In theory all driver calls are suspect, but for example I see crashes in nrf_802154_buffer_free_raw, at this assert:
This is easily reproducible by running 802154_phy_test...
Hi Team,
We want to load azure certificate into nRF9160, can you please provide sample code, code snippet to load azure certificate.
Regards,
Sravan Rikka
Summary
On NCS v3.3.0 , building any application that enables the new Zephyr OpenThread Border Router L2 glue ( CONFIG_OPENTHREAD_ZEPHYR_BORDER_ROUTER=y , together with...
Hi! This is a general info post since i have found a temporary fix to it, but whilst trying out ntn, we noticed that when switching from %XSYSTEMMODE: 0,0,1,0,0 to %XSYSTEMMODE...
Hi, we use BMD-350 modules (nrf52832) in our product which has been in production for over a year. Our DFU service is very well tested.
a couple weeks ago, while performing...
I'm planning to deploy a Thread network with 200-400 units and seeking best practices and real-world experience from the community. While the Thread spec allows up to 32 routers...
Hello Support team,
I have an issue with two simultaneous heaps in my project. I use nrf Connect SDK 3.2.2 with the next configuration options:
CONFIG_REQUIRES_FULL_LIBCPP...
