Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hi!
I've been trying out a tutorial about adding custom service and characteristics ( https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts...
Hello ,
I am having nrf52832 custom board.
In my project i need to use both CLOCK source ( Low frequency clock and High frequency clock source ).
Timer running on high...
Hello, Second time in here, thank you so much for all the support so far!
I'm developing a Beacon BLE, I wanna be able to send data over Advertising or Scan response. So...
I am trying to implement ble_app_interactive on nrf52840 as my application will require 2 uarts. I have started from the example application for the nrf58832 and created a...
in nRF52840, current consumption can be decreased by executing code from RAM instead of from flash. How is it possible to execute code from RAM? how to executing code from...
Hi, I have one nRF52840 DK and 2 nRF52840 dongles, i used the latest SDK17.0, programmed nRF5_SDK_17.0.0_9d13099\examples\ble_peripheral\ble_app_blinky\hex\ble_app_blinky_pca10059_s140...
MacOs on a macbook pro with LMP 9 (BLE 5.0 support) and a new DK2 board, SDK 16; no example built
and downloaded (SES) is discovered by the mac (same with an IPAD 2 pro...
Hi,
I need to read a digital signal with varying pulse widths (Min ~120µs) over ~30ms. Currently (nRF52832) I'm doing this using a timer interrupting every ~15µs and reading...
Hi Nordic Team：
I use this example " Thread Google Cloud Platform CoAP Example ",
I setting up the cloud is finish, but I Thread device of google_iot_coap not join the...
Hi everyone,
I'm new with nordic chips and for our project we use a custom board based on the famous nRF52840 mcu. I read a lot about SDK17 in the infocenter to find how...
Hi
The latest OpenThread/Zigbee SDK has no examples for openthread with the PCA10059 (No MBR, executing directly from 0x0 @ flash start).
Ive tried now multiple times...
nRF52840, SDK 16.0.0, SD132v7.0.1
What's the correct way to tell whether HFXO or HFINT is clocking the HFCLK controller? I'm able to start and stop the HFCLK controller...
Hi, i am using the nRF52dk would and im using the pwm driver example and im trying to understand the way the seq_values void works when it comes to phase or sequence would...
Hello, I uses the NORDIC project saadc_low_power. A counter was built into this so that only a defined number of samples are carried out. Measuring current on an nRF5 DK while...
Hi,
I have a custom PCB using the Johanson 2450AT18A100E chip antenna. For some reason, I'm getting extremely subpar RF performance and so I'm taking a second look at...
