In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi,
We would like to know the default state of the NRF52840’s GPIO pins - is it high, low or open? The reason for this question – we need to know these pins’ behavior/state...
Hello Guys, I want to build some project with Nordic products but ı don't have any sample code , if you have sample code for Keil let me improve myself.Actually codes can...
Hi,
As has been explained numerous times in posts on this forum and many others, mapping RSSI to a distance measurement is notoriously difficult and inaccurate. I was...
Hi
Can anyone verify that it is possible to use the nRF5340 PDK to program custom nRF53 board?
The documentation says: The nRF5340 PDK supports programming and debugging...
Hello,
we are using NRF9160 +Nrf52832 in a project. NRf52832 has to be used as HCI interface..after searching for this, i came to know that zephyr based HCI uart sample...
Hi,
I am working on Eddystone project, after I successfully tested the Buttonless DFU example, I added DFU service to Eddystone example ( nRF5_SDK_17.0.0_9d13099\examples...
I am using this MBN52832DK and find out this nRF5_SDK_17.0.0_9d13099.
Trying to import into Segger Embedded Studio but rebuild come out error.
using the nrf52832_xxaa...
Hi all,
I would like to have a semi-duplex communication link over one pin (+GND). The nRF will act as a pure slave device which responds to, and acknowledges, commands...
Hello, we understand that the Nordic framework, by default, restarts advertising on disconnect. I learned that here, thank you:
https://devzone.nordicsemi.com/f/nordic-q...
I'm currently running on nRF Connect SDK (hash: 4b012fb4882f0ddd3de9f339ebc5a3f1c3cacd4a). I'm running a connection between a nRF91+nRF52840 (as central running NUS_C) using...
I have an nRF52840 board that fails to connect to Linux over USB. The board powers on and the green LED at the lower left of the PCA10056 flashes on/off rather quickly. But...
There is a bug in fds.c file, Please go through the below code snippet.
I do not return from fds_gc(), execution stays there for infinite.
More information:
1) #define...
Nordic nRF52840, with regards to stored security keys in flash, some wear leveling schemes move data when being updated but do not erase data from the old location. This is...
Based on several posts I've found on the forum, the notification queue size is automatically set by the stack based on the connection event length (NRF_SDH_BLE_GAP_EVENT_LENGTH...