Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
sdk: nRF5_SDK_11.0.0_89a8197 routine nrf51_ble_app_hids_kbd_consumercontrol-SDK11 can adjust the volume of Android phone, or adjust the volume of the laptop
sdk: nRF5_SDK_16...
Hi,
I'm currently porting a project to nRF5 SDK17. Some time ago we decided to use the nrfx module as a fork of https://github.com/NordicSemiconductor/nrfx .
So I synced...
I'm working on a switch device using nRF5 SDK for Thread and Zigbee version 4.1.0 on an nRF52840 on a PCA10056.
I can get my device to join a network, and can see that the...
I see that Apple finally played their card in the consumer asset tracking device space last week. the "Find My" network will be available to third party devices. Details are...
Hi,
I'm working on the Basic example Blink_led.
I would like to change from LED 1 to LED 2. I changed the ch0-pin = <3> in the nrf9160_pca10090_common.dts but now the...
I would like to implement firmware update of nRF52832 through UART from Linux SoM, do you recommend following the DFU procedure or implement custom bootloader? I don't need...
I am using the 9160DK (0.9.0) and testing the PSM and eDRX modes with ncs V1.3.0. if I program the Asset_tracker without any changes I can connect to the nRFCloud.
from...
Hi
Unsopperted device. The detected device could not be recognized as neither JLink device nor Nordic USB device
I believe nRF connect programmer can't fint nRF5340...
On reviewing Zephyr SDK V1.3.0-rc1
I am able to build and run the soc_flash_nrf example as a nrf9160dk_nrf1960 board all works as expected.
when I try with nrf916dk_nrf9160ns...
Hello!
I am working with the nRF9160 devkit and I have encountered an issue.
I cannot seem to properly enable PSM to use the GPS and LTE at the same time.
In the application...
Hello, For our project we were planning on using a 3rd party module MS88SF2 (nRF52840), which schematic snapshot is provided and which will be powered though the li-po battery...
Hi guys,
I am using the Nordic nrf52832 board for my project. One of my goals is to enable the device to read the voltage from the external source. I have already found...
I think I am having a problem with Radio Notification. I am not sure. I have an application where I need simultaneous “Central and Peripheral”. Device only needs to advertise...
I am trying to do Mesh DFU.
I have done updating ble_app_blinky successfully for the 1st time over mesh but after that, I tried to do again by increasing the application...
