How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hello
In the radio test we can set up to 80 channels.
But isn't the table for the channel as follows?
40 channels is 2480MHz, right? What is the frequency of 80...
Hello
we are working on Audio project with nRF52840 include (microphone and Audio Amp). we used one I2S interface for Audio Amplifier but for Microphone we are confused...
Hi there,
Please let us ask about SMP server sample. https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/samples/subsys/mgmt/mcumgr/smp_svr/README.html#smp...
Hello All.
We are planning to do a EMC test on our device that is using nRF52832, the test facility requires us to provide a programming interface that can change the...
Hi!
Can't continue here:
https://devzone.nordicsemi.com/f/nordic-q-a/56211/bootloader-difference-and-implementation-from-sdk-14-to-sdk-16
So I've made a new question...
Hi
So I tried to use the lwm2m sample client (nrf\samples\nrf9160\lwm2m_client) for FOTA upgrades. I do get a connection to my plattform. When I start the update I do get...
I'm trying to figure out how to change the start address of my application when chip has a bootloader flashed on it.
For example :
Bootloader address = 0x0
Main application...
Hi,
Fairly new to the world of nrf development and C programming so apologies for the potential newbie question.
I am looking at how I can setup a Raspberry Pi 4 as...
I have an application that uses the nRF52840 for BLE in central mode. This application is battery powered. Basically, the device is listening for beacons and logging which...
I'm trying to connect to a device with a public address using an address filter in the scan (not whitelisting), I've seen plenty of similar unresolved issues posted here....
I am searching for the zip with reference designs and PARTNUMBERS for the nrf52 series. The datasheet link is broken and I can not find the ZIP file in the new Help Center...
Hi,
I'm trying to use the serial number of the nrf52832 microcontroller in code, how can I acess it with Segger.
I tried using this code from this link but it doesn't...
Hello. We are planning to change from QFN48 to WLCSP package in our product. However I could't find any guidelines to create the library for Eagle. I was wondering what is...
Goodmorning,
we are trying to update the firmware on a nRF24 development kit board (nRF2727) that was programmed with the PTX sample from your software development kit....
Is there a document comparing the differences between the softdevices for the 51832 ?
I have been looking at the data sheets, but its too much to grock on my own.
Thank...
