Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I have some issues sending valid information to nRF Connect app by bluetooth using the Aduino Nano 33 BLE with nRF52840 on it. I am using Arduino IDE and the ArduinoBLE...
Hi all,
The project I am working on consists of a BLE peripheral, a BLE central and an enhanced shockburst device. I run into a problem in the code of the peripheral:...
In a project based on Softdevice S132 7.0.1 employing the Softdevice timeslot API, I noticed that the nrf_radio_signal_callback_t function passed into sd_radio_session_open...
Hello,
I am using UART_1 to receive GNSS data. For UART_1, baud rate is 115200bps. On terminal, I can see the correct data when baud rate is set to 115200bps. When the baudrate...
Hi, i am using nrf52840 development kit , four servo motor . using 15.2 sdk version
here i am controlling the angle using adc values , i am done with one servo motor . pwm...
Hi
I am modifying the scanning and advertising paremeters for coded (125kbps).
I made the following changes in advertising
.primary_phy =BLE_GAP_PHY_CODED, instead of...
Hi All,
I am using nRF52832 SOC for my development. I would like to buy a packet sniffer for my BLE development.
Can someone please suggest a suitable device for this...
Hi
In the SDK, Replay_Cache_Entries is assigned a value of 40, which means that Replay_Cache can only process 40 unicast messages. That limits the maximum number of unicast...
Hi,
I am using
nRF52840
SDK 15.3.0
Keil IDE
The soft device is S140
JLinkRTTViewer for debug
Device has both Central & peripheral functions.
It takes about...
Hi,
I used(SoftDevice 140, based on the ..RF5_SDK_15\examples\ble_peripheral\ble_app_beacon )
m_adv_params.properties.type = BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED;...
Hello Everybody,
Here are two patches for nRF5_SDK_15.3.0_59ac345 to make the ble_app_uart compile as a C++ application with GNU Tools ARM Embedded 8 2018-q4-major.
nrf...
We are currently experiencing a problem during development of Medical device.
We are currently using nRF52832 on Thingy52 prior to bring up on the product board having nRF52840...
Hi!
I am trying to send over SAADC data from a peripheral device over BLE to a central device. Currectly I have sucsessfully merged the SAADC and BLE_UART peripheral example...
