In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi,
I want to test ble_app_tile project in SDK 16.0.0.
The project needs to install pack NordicSemiconductor.nRF_DeviceFamilyPack.8.27.0 in Keil 5.
However, I did some...
Hi,
Need data on Stencil , recommended solder profile & Solder paste details for nRF9160.
We are facing some issues in production.
*Critically Urgent *
thanks !
Hi,
We made an online course on Bluetooth Low Energy, includes BLE Fundamentals & Architecture, step by step implementation of Environment Sensing service development...
Hi,
I am trying s112 on pca10040 with SDK16.0.
I found that I can't build the app whenever I use the " nrf_ble_gatt_ data_length _set() " api... does this mean that s112...
I'm using the socket(AF_LTE) to talk directly to the modem on the nrf9160 and wanted to add a timeout to my recv() call. I added a call to poll() before recv() and am seeing...
Hello,
nRF51822
SDKv11
Kail 5.18
SD130
I have a pcb that has a sensor with I2C. I made a project that based on the sample of "twi_sensor", and I can read the sensor...
Hi all, I am trying to build the beaconing example from the nRF5 SDK for Mesh. When running:
$ ninja flash_beaconing_nrf52832_xxAA_s132_6.0.0
I get the following error...
I have 3 nRF52840 dongles and want to setup a mesh network between them. Which example from the SDK should I execute and how will i come to know if its working fine.
Hello all!
I'm using a nRF52 DK, which has been already programmed with the soft device s212, since my interest is to be able to connect to sensors using ANT+.
My purpose...
Hi,
We are currently testing DRX (not eDRX) on our custom board, and we would like to reduce the power consumption.
When everything on the board is in low power mode,...
Hi Goature,
We are also try to implement the same. We aren't getting any idea how to start. Refer the same thread : devzone.nordicsemi.com/.../make-ble-central-send-firmware...
Hi there,
Is there any Zigbee Motion Sensor code example that someone has put together? I could not find any on the nRF5 SDK for Thread and Zigbee.
Thanks
Hello,
Was programming two different boards today with the new 1.1.0 modem firmware.
Programmer reported the following for the two boards.
2019-11-21T21:10:34.297Z...
Hello!
Some time ago you seem to bundle sample 5 x nRF52832 to nRF52DK. Recently there was no bundled chips. Why did you change that?
The development and prototyping...
Hello, I tried to set up my nRF9160 with this tutorial and there is a problem: https://www.youtube.com/watch?v=jZQcmU3KIMY&t=216s
According to the tutorial, LED 3 and the...
