Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have a strange bug, that I do not have any good answer for.
In the software, I use either SPI1 or SPIS depending on current configuration, I have seen some rare cases...
I know it's not very common to use a secondary service, but I want to use it in one specific scenario. When referring to the documentation for the API sd_ble_gatts_include_add...
Hi,
I'm trying to use the LPCOMP of the nrf52 telit board.Configured lpcomp with the following settings :
Input : AIN2
Ref : AIN1 ( external ref. of 1.6V)
Detection...
Hello I am using PCA10040, nRF52832, and GCC toolchain
I have a project that was working good using sdk v12.3 but now I want to migrate to the latest and I am getting one...
Hi
After the device has been in idling, the sleep_mode_enter function is called which then calls
sd_power_system_off().
The device then goes into sleep mode until a...
Hi! I need your help!
I need to create some mesh network consists of simple devices (A) which could collect mac addresses of all visible Bluetooth devices (C) and send it...
Hi, I try to mount some I2C devices at Arduino Primo but I can not get any results. I tried an I2C LCD that did not return any error but did not display any text. When I scan...
Hi,
I am using IAR for the pca10056 with a nrf52840 chip. Can I change the compiler in IAR? I simply just downloaded the newest version from the IAR homepage and specified...
Hi I'm trying to compile the experimental_ant_bootloader for the pca10040 with a S212 soft device using the armgcc compiler using SDK13
I can't find a makefile or linker...
How do you do
1.In the Nordic \ nRF5_SDK_12 _f012efa 2.0-3 d \ examples \ peripheral here, there are three PWM routines:
Low_power_pwm, pwm_driver, pwm_library but only...
Hi, there~~. The PCA20006, nRF51822 Bluetooth Smart Beacon Kit, is fascinating!
So I'm planning to create a custom beacon product of my own,
a 2-layered PCB with nRF52832...
I have trouble programming the PDK using nrfjprog. I can flash the program fine using Segger Embedded Studio but it doesn't appear to be working using nrfjprog.
Here are...
When using ble_app_uart, I set the advertising timeout to 10s, but after the timeout did not enter sleep, but automatically reset,my judgment is based on the terminal to send...
Hi
I have run this example code
nrf5_SDK_for_Mesh_v0.10.0-Alpha_src\examples\light_switch\client\light_switch_client_nrf52832_xxAA_s132_5_0_0.emProject
when I operate...
I want to reprogram a nRF51822 xxAC device on a existing product.
I have a J-Link (SEGGER) device with latest firmware.
I'm running the SEGGER J-Flash V6.20e utility.
I...
