Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi,I made a 52840 board ,it's p0.18 hanging, without connecting a 10k pull-up resistor and a 100nf capacitor to ground. I connected 3v3, GND, SWDIO, and SWDCLK from the 52DK...
NRF54L15 NCS 3.02
I have to change my BLE advertising from Legacy to Extended. Looking at the Zephyr example "advertiser" which compiles & runs fine, but I notice that behaviour...
Hi,
I am currently trying to connect a nrf52811 as an companion to an ESP32 user UART.
I am using the interrupt driven UART implementation as kind of the last resort....
How can I set a custom interval for *extended* advertising?
I'm currently calling bt_le_ext_adv_start ( struct bt_le_ext_adv * adv , const struct bt_le_ext_adv_start_param...
~~~~~~~~~~Environment ~~~~~~~~~~ nrf54L15 + NCS 3.1.1 + VSCode + Win11 ~~~~~~~Reproduction Steps~~~~~~~~~ 1. without pm_statics.yml, with following configs (see attachment...
Dear Team,
I am experiencing a weird issue with the firmware on my custom EV board with NRF54L15.
My firmware is using MCUBoot and partition manager (I use a separate...
Dear Team,
I need to switch LXFO to internal RC for MCUBoot, however, I am experiencing troubles configuring it on NCS 3.0.1 (NRF54L15).
If I just add my RC settings to...
Hi,
Our project requires an unusual combination of running BLE, Gazell, and raw radio packets for time sync simultaneously.
Time sync and BLE are infrequent activities...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Hi,
I've run into an issue when doing some compatibility testing between our client's legacy device (802.15.4 transmitter) and the current device in development (802.15...
In the introduction to the bare metal SDK option for the nrf54L:
https://www.youtube.com/watch?app=desktop&v=31znTI-hnCQ
it mentions at around 58:00 that single bank...
I am using nrf connect SDK toolchain version 3.1.1 and nrf connect sdk version 3.1.1 , By default I don't have zigbee related samples/examples and also zboss stack library...
The original question was: "The nRF52840 PS mentions, that this chip contains an ETM but it does not mention the implemented version."
Researching the topic more, I found...
Hello Team,
We have noticed a very weird issue with the nRF5340 Audio DK. After flashing the audio application code given by nordic, everything works perfectly fine. No...
