I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
hi,
i am using NRF52832 DK, and sdk 15.0.0.0 ,,
i want make the central to work also as a peripheral...i.e whenever central is not working ,or ,central is not in connection...
I am evaluating the throughput of BLE communication between 2 NRF52832's, 1 acting as a central and 1 as a peripheral. I've modified the ATT_MTU Throughput Example, and I...
Gone through sdk 11.0.0 Experimental_ble_blinky application, i trying to assign one gpio pin in place of connected LED. what is it receiving when pressing on & off switch...
Hi,
I'm working with nRF52832 chip following the example "ble_app_beacon". I see the advertising packet is limited to 31 bytes only. However, I'd like to take an advantage...
Hi,
I have arm based application processor and need to connect with nRF52840 using UART, I don't have any idea about bootloader and factory firmware when hardware assemble...
We are trying to determine the emission designator for the nRF52832, or at least to determine the necessary bandwidth so that we can create the emissions designator. Please...
Hi everyone,
I have a problem with SOME android devices.
In particular Android devices with BLE 4.0 & 4.1, but I have NO problem with Android device with BLE 4.2 and iOS...
Hello,
We are using nRF52832 DK with SES IDE and latest SDK 15.0 sd 132. We have developed one multiplink central device and modified ble_nus_c with our application to connect...
I use nRF52832,is 2.5v power supply,but you can't download the program,w hen I set the voltage above 2.8v, I can download the program,then I switched the voltage to 2.5v and...
Hi everyone
I am able to send the data over the UART to the Real Terminal and also to my other device working on UART protocol. However , I am not able to read the data...
Hi,
I am willing to migrate sdk 14.2 code to sdk 15.0 code. Do you mind me to ask a crypto micro-ecc question, please? Thanks.
In sdk 14.2, the micro-ecc part definition...
Hi,
I am working on nRF52832 board using Segger Embedded Studio for ARM 3.34a on windows 7 64 bit setup.
When I am trying to initialize a structure in Flash memory, the...
I'm developing TWI code for Bosch BNO080. They use SHTP protocol on top of TWI. A working version using Wire library of Arduino is posted here .
I ported the code, and...
Hi there,
I'm playing around with the stock hrs_relay example that I've modified. the code works well but I'm noticing that its advertising strength is crazy high.
I was...
