In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
I use NRF52832 and sdk13.0.0 to develop my own application. I want to generate 1000 Hz Timer to trigger the ADC. I use the timer 1 to generate 1000 Hz. But when I use GPIOTE...
Hi,
In Nordic nRF51822, (please correct me if I am wrong), after I transmit 1 byte of data (since the transmit fifo is 1 byte long and receive fifo is 6 bytes long), I can...
Does the python driver support multiple dongles? I have a situation where I want to scan with one dongle and connect to devices with a second dongle. However, the collector...
Hello,
I want to use the PCA10040 to program a custom board running on 1.8V using the debug out port. Is this possible?
Also, is there a way to set up the PCA10040 so...
Device: nrf52, sd132 v3.0.0, SDK 12.1 (and also 12.3), freeRTOS, BLE peripheral, gcc-arm-none-eabi-5_4-2016q2
I am experiencing an issue which is causing our device to...
Hi everyone,
I am developing a remote control using nRF52832 chip. My prototype is currently developed in PC10040 board. The IDE is Eclipse Oxygen, and the SDK is S132...
Hi, now I'm using NRF52832 's UART with SD12 and it required to receive 40 bytes per 10ms.
In fact, it does not take 10ms to complete the reception.So my idea is to create...
Hello,
I'm working on a type of activity tracker using the NRF52, and I'm a bit stuck with time aspects.
The device stores two versions of activity data; daily totals...
Hi
First I wrote a post because the initialization was crashing, but now I found out it was because the RX line was low.
How to initialize the uart if the RX line is low...
hi i have a problem with ble app uart.i used nRF5_SDK_12.3.0_d7731ad and Eclipse Mars 2.
I had build main.c in hex ble_app_uart\pca10040\s132 . And after that a maked mergehex...
Hello,
I am trying to update our application with DFU support but it will not work for me. One of 2 things happens:
Programming the bootloader and softdevice by programming...
Hello,
We have the following setup:
SDK Version: nRF51_SDK_8.1.0
bootloader Version: dfu_dual_bank_ble_s110_pca10028.hex
soft Device: s110_nrf51_8.0.0_softdevice...
Hello,
I'm working on a concurrent role device (advertiser+scanner+peripheral+central) and devices are configured to connect each other in a mesh-like way (Note: I'm not...
Hi,
i am using ble_app_hrs_c_pca10056_s140 and when connected to one particular device i need to access it's GATT profile services and characteristics.In example ble_app_hrs_c_pca10056_s140...
