Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
We have a product that uses nrf51422_CE_AA, Revision 3, 256KB ROM, 16KB RAM, PCA10028, SDK 8.0.0, S110. We have sold over 8000 devices of our first product. Currently we are...
Hello,
My problem is to much current c.a. 40uA in POWER OFF mode. Below attach code:
void power_down()
{
nrf_gpio_pin_clear(22); // Wylacz mostek tensometryczny
nrf_delay_ms...
With nRF52832 DK I have managed to compile this blinky example:
#include <stdlib.h>
#include <stdint.h>
#include <stdbool.h>
#include "nrf_delay.h"
#include "nrf_gpio...
I am getting no radio (as in not being able to pick up advertisements packets) from my custom nrf52832 board. The antenna design is a hack so I am not looking fo stellar performance...
We are looking in to developing a generic class to connect and handle our BLE devices for use on mobile devices such as Android and iOS.
Now since we want to have as less...
Hello Experts,
I am running the following examples to test the DFU bootloader in gcc and eclipse environment.
bootloader_secure/pca10040(Bootloader) and experimental_ble_app_buttonless_dfu...
I found a problem of the nRF51822 in boot state.
Power on reset is not executed occasionally when used dying battery.
The problem occurs in the following steps:
...
Hi All,
I'm having a BTLE_CONNECTION_TIMEOUT when I connect the device in Master Control Panel 3.10.0.14 while the chip is not in debug mode.
The device connects without...
Hi
I am trying to upgrade the firmware in a BL652 using a Segger Jlink Edu.
The BL652 is powered with 3.3v using a regulator off the JLink 5v output.
I had poor/unreliable...
I am using a processor that can provide an 32KHz clock (from its crystal).
Can you recommend the voltage divider (caps or resistors and suggested values)?
I will power...
I added a task to ble_app_hrs_freertos.
The soft device was burned.
The address is in the default state. (RAM:0x20002128 ROM:0x1f000)
I reset the total heap size...
Hello i am quite new to using BLE for data collection. I am using a Readbear BLE Nano with a Nordic nRF51822 on it.
I want to read a Sparkfun MMA8452Q accelerometer's X...
Hello, if I disable interrupt on nrf51xxx device, function sd_ble_tx_buffer_count_get will simply run right into hard fault handler, without returning anything.
I do not...
Hi,
on NRF51 BLE peripheral I want to implement authentication, so only selected BLE masters have access to my BLE peripheral.
There is a password known to BLE peripheral...
