I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hi,
I use SDK 12 softdevice 130 2.0.1
The example project of HID is running on my nrf51822 board, it is pairs with iPhone but the windows 7 write that the HID driver...
Dear,
I am now testing Power Profile Kit. Using nRF52 DK.
But Strange, Measured Value is strange as attached picture.
Is there any problem on my measurement or setup...
Hi there!
I am trying to develop some application using ANT, and for that I bought some nRF51 (10031) dongles and one nRF51 DK (10028). In the beginning, I tried to use...
We are trying to dump SDK 12.1 examples and advertise the example, we used Segger embedded studio to dump the code, bps example. we followed devzone.nordicsemi.com/.../ to...
Hi,
I'm using an nRF52832 with the S132v2 and SDK 11 and wanted to test the ble throughput.
The nRF52832 should send as many as it can to an "normal" BLE-USB-Stick.
...
In SDK 11 the FreeRTOS port has the following line is declared in portmacro_cmsis.h
#define portNRF_RTC_PRESCALER ( (uint32_t) (ROUNDED_DIV(configSYSTICK_CLOCK_HZ, configTICK_RATE_HZ...
After updating from sdk11 to sdk12, the application only starts in debug. If started with reset, it hangs. I am running on a pca10028 board an with EmBlitz 1.0. NRF51 is QFACA1...
When I test the example, When I disconnect my phone of the nordic board.
I can use the other Phone to connect the nordic board
So, I think that how to avoid the connect...
I compile blinky_pca10040
I use IAR EWARM - ARM Cortex compiler
I have a Rigado BMD-300 on my PCB
Use J-LINK EDU
When I try to download and debug, I get the error
"Failed...
Hi
I came across this article:
www.nordicsemi.com/.../Bluetooth-Smart-hearing-aid-receives-stereo-audio-direct-from-iOS-devices-and-can-recognize-and-optimize-settings...
Hi, I want to change some configurations of my beacon such as packet type, UUID, Tx power and so on, in an online manner through the Bluetooth connection(by an application...
Hi I have run into this error when running. However it has just appeared (the FDS did work but now will not initilise.) I am using Visual_gdb.
As per this issue
I have...
Hi,
I am using nRF8001 with a MCU from PIC18F family. I have successfully configured nRF8001 to send and receive data through the nordic UART pipe (I used the app nRF UART...
