Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
I wrote an application that works using an Enhanced Shockburst-compatible protocol (because I need it so), using the RADIO interface.
What happens if a packet with an address...
Hi U guys
First I’m pretty new I use of bluetooth low energy, so bear with me.
It is pretty simple, I need to send a temperature each 10 sec. or whenever it has changed...
Hello. The nRF51822 Series Reference Manual says on page 38, "The SWDCLK pin
has an internal pull down resistor and the SWDIO/nRESET pin has an internal pull up resistor...
Tunning connection parameters to minimize current consumption for a fitness device transmitting data to ANT+ and BLE at 1sec intervals.
The desire is timeout after 60sec...
Hi,
We are trying to use the over-the-air bootloader in our application.
Our problem is the bootloader seems to require one first over-the-air download before it allows...
Which pins are mapped as ADC inputs for the NRF51822? I've pored over the documentation, but I can't seem to find which ADC pins (AIN0 to AIN7) correspond to which GPIO pins...
Hi
My aim is to be able to update the application code OTA in a 128kb chip (version nRF51822 QFABB0). First, I want to use the nordic original code to discard any other...
Hello all -
I'm trying to learn about the db discovery module from the perspective of the BTLE central and I'm a little confused by the client architecture. The SDK documentation...
I'm developing an application for a device which needs to support DFU service,
If my device get the specific packet over BLE (like 0xd1), i want to start dfu service. ...
I'm trying to study Message Sequence charts under the BLE GAP (Generic Access Profile) section of the s110 soft device.
However, I've noted that multiple links don't seem...
Hi
I'm studying at university and working on my thesis.
What I'm doing with a remote control and I want to measure the impedance of the antenna, because I want to be documented...
Using: nRF51822-BK-FW (v 1.0.1).
From within, there is the source files for ble_app_beacon_bcs that when compiled/loaded on the beacon hardware, causes the LED to blink...
Hi. I have been trying to follow nAN-29 to migrate from Keil to Eclipse without success. I was excited to find the blog, devzone.nordicsemi.com/.../ . The blog suggests that...
Hi all,
I just had some general questions regarding events and timers on the nRF51822. I'm coming from a Ti CC2540 8051 which used an OSAL system. This made it quite easy...
