In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi
As described in this white paper: https://infocenter.nordicsemi.com/pdf/nwp_036.pdf during the reference period of CTE signals, 8 samples are taken. These samples contain...
I’m using the DECT Shell perf command to evaluate DECT NR+ performance.
Could you please clarify the units and scaling of the snr field in nrf_modem_dect_phy_rx_pcc_status...
Hi,
What file or files should contain CONFIG_GPIO=y for a simple application developed with nRF Connect SDK v2.9.0 such that VS Code does not show squiggles under #include...
Is there any point to using deferred logging with the RTT backend?
The way I understand RTT is that it writes the message to a buffer where it is fetched via DAP, skipping...
Hello,
I'm trying to implement runtime power management (SDK 2.9.0), but as soon as I enable the option, the shell and logging on UART0 stop working at startup. The rest...
Today I bought a new NRF-PPK2, but compare with my old NRF-PPK2.
For the old and new PPK2, I use the same DUT.
It can't show the same current with my old one? can you...
Hello, We are developing an application with nRF52810 based on nRF Connect SDK V2.4.1. The application is utilizing the BLE connection, particularly the NUS Service (emulation...
Hi,
In our project, we are planning to use the nRF9160 for both LTE-M and Wi-Fi. Thus, we have connected the nRF9160-DK to the nRF7002-EK in the developing phase as we read...
Greetings developers,
I am using nrf connect sdk 2.7.0 with nrf52811 soc. 1) present situation:
My application sequential in nature and does not have multiple thread...
Hi,
I am failing to build any of the Matter, Thread or Zigbee for nrf52840dk with the following failure.
I successfully build a blinky and bluetooth app, so my tool chain...
I am trying to use fstorage with the sd backend (SDK 14.0.0). My issue is that, after successfully calling nrf_fstorage_write, the callback I registered using
just never...
Hello,
I'm developing a program on a NRF52840 DK in the SEGGER Embedded Studio IDE that outputs a PWM signal when a Bluetooth Mesh GenericOnOff signal is recieved.
I got...
Anyone knows why I'm getting this result? I'm building the application using sysbuild and flashing normally on nrf52840dk. I tried both following all the steps in the lesson...
Hi,
i am trying to create an Indoor Positioning System with the nRF54L15.
Currently i am able to connect 1 initiator to multiple reflectors simultaneously,
When...
i have used same Serial_lte_modem sample code from nordic toolchain 2.6.0 , Enabled shell just by setting config macro
CONFIG_SHELL=y and SLM uart loging is by default...
