Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi! What is the proper use of sd_ble_gap_adv_stop in SDK 15? I'm using nrf52832 in my application but can't seen to find a corret way to stop advertising.
Looking on ble_gap...
Hi all,
I'm using Raspberry Pi with Nordic dongle and flashed the Nordic Alpha 4.1.0.1 image to make it as BorderRouter in NCP design.
I have EFR32device and have flashed...
Hi
I'm using nrf52832 custom board with 14.2.0 SDK version and trying to communicate TWI interface with LTC2631 DAC converter. I tested my sensor hardware with Arduino and...
DK 52840 DK
description ： for example ：we use 52840 DK start a adv at 37 channel,when this packet transmission finished， the radio will change from TX to RX，so how we get...
Hello
I am working on BLE custom board NRF52832 design. I have made 3 PCB for it and out of three, 1 PCB working fine and rest of the two connects with the BLE but doesn...
Brand new Thingy91 PCA20035 out of the box.
Plugging in the USB and turning it on, the nRF Connect Programmer alternates between 'Select device' and 'No devices available...
Hi, after a couple of months of inactivity I try to rebuild my Zephyr-based application under nRF Connect SDK, tag 1.3.0. I’m dumb-founded to see this unexpected print hereunder...
Hello,
Is there any complex documentation how to implement MSC on custom block device ?
I need to implement NAND flash memory in specific way, but I don't understand how...
Hi,all
How to filter the scanned broadcasters by short name ?
I have been set 'CNT' define, and compiled without any errors,and it worked, but the filtering strategy didn...
Hi,
To automate some testing procedures, I was wondering if it is possible to use the firmware, which runs on an nRF5x to connect to nRF Connect for Desktop, but with a...
Hello all,
I'm fairly new to BLE and Linux BlueZ.
I'm trying to interface a Mikrobus BLE module based on nrf52840dk to our Yocto based Linux SBC (Rugged board i.MX6-UL...
Hi Nordic Team,
I am new to embedded developing and I am learning about logging data while working on nRF connect sdk" .
kit:nrf5340
SDK: nRF connect SDK v1.5.0...
I'm finding that the MCUBoot stays stuck in bootloader mode sometimes when using a CONFIG_BOOT_SERIAL_DETECT_PORT.
I've narrowed it down to setting up the GPIO as input...
