I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
Hi.
I'm new on this form and also new on nrf dev board. I want to use OLED with nrf52832 using Twi / i2c. I grab some code on Github https://github.com/monpetit/nrf52-spi...
Hello , I am trying to develop my own application using ble mesh sdk in nrf52840 provided by nordic.I have gone through various examples and various blogs.
I want to know...
I'm using NCS v1.5 and nRF52840
I'm trying to achieve low power consumption.
I turn on scan using, which draws around 9.5 mA.
What I'm then trying to do is turn scanning...
Hi, I want to create bootloader for my code. For that I have install Python3 (Python 3.9.1)
followed by installing pip and nrfutil
python -m pip install --upgrade pip...
I use sd_ble_gap_device_name_set to set 10 chars device name
then getting NRF_ERROR_INVALID_LENGTH in sd_ble_gap_adv_set_configure.
all OK when tested 3 chars device name...
Good morning,
I am developing an application that needs to match a central with a specific peripheral. For this, the first time they connect, the address must be saved and...
Please allow me to introduce myself, I am product Engineer at Epson Electronics. I am supporting Nordic on Reference Designs.
I noticed in the new nRF5340 there are two...
Hi Nordic:
I think this should be a same old question, but as following thread mention:
https://devzone.nordicsemi.com/f/nordic-q-a/38292/mesh-proxy-sdk2-1-1-tx-power...
I am attempting to provision the sensor mesh example using the static provisioner example from the MESH SDK.
It works great. However, the client receives two broadcasts...
Hi community,
Starting with a new product on the nRF52, I was playing with the Serial Flash of the nRF52840 DK.
I have been using similar Serial Flash on other platforms...
Hi !
I'm trying to debug. I followed this video : https://www.youtube.com/watch?v=uP8RYgYGRvI&list=PLx_tBuQ_KSqGHmzdEL2GWEOeix-S5rgTV&index=7 . But I can't completely. ...
I would like to use nRF52 DK (nRF52832) to program Fanstel BC805M EK (nRF52805) . When I upload to code from nrf52 DK to BC805M, I got this error message.
I know that...
I have many of these types of systems running in a single room but when I try to run more than 8 I start start to get errors. How many systems should be able to run in the...
I am creating a saadc project based on the ble_app_uart project.
The source code is as follows.
If you download after compiling, the following operation is performed...
Hi, all
I am studying the bsp part while looking at the example of 'ble_app_uart'. (pca10056)
The difference between 'bsp_event_handler' and 'bsp_button_event_handler...
