I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
i want to send string over eddystone tlm...and wish to use temperature part for this...so how can i display character string instead of temperature in eddystone TLM..please...
Hi, I am trying to use the iOS nRFMeshProvision SDK to create a iOS mobile application. I am trying to get the composition data but access layer always times out and gives...
Hi, I am new to Dev Zone. I am writing debounce logic and I am wondering if a button can have an interrupt set when the GPIOTE sense a HITOLO transition to fire the first...
Hello, I'm currently developing BLE_SCANNER(GATEWAY) for asset tracking or management.
My scan environment is,
[Our device -- same UUID]
The number of our beacons...
Hello. I have the same problem with https://devzone.nordicsemi.com/f/nordic-q-a/54373/uart-logging-backend-hangs-in-nrf_bootloader_app_start/220132
But this thread was stuck...
I'm trying to register a handler to determine when a system event occurs?
Previously on older design kits, I used softdevice_sys_evt_handler_set(......) to register the...
Hi,
I've managed to code an app for nRF52382 (S132, SDK14) which works properly. Also, I've taken "bootloader_secure_serial" and removed a lot of stuff to code a simple...
To the kind attention of Nordic support team,
I've just downloaded a fresh copy of nRF5_SDK_16.0.0_98a08e2.zip.
I would like to download code in nRF52810. The code in...
I want to make a programmer for nrf52832. Do you know where is the documentation of SWD is ?
Note: I found the similar question, but the links are not active
Hi
I am using Segger Embedded Studio and SDK_v15.3.0. I have a C++ code that I wish to run on the board. It has a lot of printfs. I want to see the output of the print statements...
Hi,
I'm new to Nordic Semi chips (nrf52840) and need to use TWI as a master to connect to two sensors. But I'm a bit confused about the different drivers: TWI and TWIM....
Hello to all,
I have a problem related to the client side Global Attribute: I have implemented an "On / Off Switch" that presents the cluster On / Off (0x0006), client side...
Hello,
When we analyzing the traffic of our application (many thanks to the team developing the sniffer), we have several questions about sending write confirmation.
for...
We do have a product in which we program a bootloader on the target. It is remotely based on the ble_app_buttonless_dfu example. The bootloader is not actually used in the...
Hi I am building a software watchdog to monitor nrf52 peripheral states to have higher confidence for 10+ years battery lifetime. The idea is to check every few seconds if...
