Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello, i want to know is it possible scan iBeacons with a node using nrf mesh with proxy features like the light switch node server example? if this is, how i could start...
Hello.
I have pa/lna on my device. It works properly in application (rssi is about 30 dbm). But when application goes into bootloader (dfu over ble using nrfconnect on android...
Hi, I'm using the nrf connect mobile app and I want to connect multiple devices to the advertising device and I want them all to access the same characteristic at the same...
When I open SES it says that it cannot detect any j-link so it asks me to buy license. But shouldn't my nrf52840 dk board have on-board j-link that SES should detect? I check...
Hi,
as I understand (and tried), in order to get low power consumption on the NRF91, I need to to get CONFIG_SERIAL=n.
However , I need the uart to be enabled (for short...
Hi - I am wondering what is the power optimal way to read/write with the TWI module. I do a tx and rx with the TWI interface. I have something like this, from the examples...
Hi,
We have just almost finished develop a product which used nrf52840 as a data hub, a wifi module connect to nrf52840 through uart, and baudrate set to 460800, and also...
Hi ,
I am using the example "ble_app_uart".
I enable uart while receiving data from nus handler and turn it off after transmitting.
After I mondified the code, it can...
When trying to write the bootloader hex file to the device with nRFgo Studio, the following error message is displayed.
[nrf52840_xxaa_s140.hex programming failed: This...
Hello
I'm using SDK 15.2 on nRF52 DK to test the ble_app_multirole_lesc example.
I downloaded the code to nRF52 DK to act as central.
I commented the scan_start() function...
I take bootloader_secure_ble example for pca10056 build it and use hex file to program using nRFGo Studio get error verification Failed. if i programmed with keil then load...
HI,
I'm having a problem when I use the function nrf_drv_twi_xfer. The function returns the error code NRF_SUCCESS, but using the event handler I notice that I'm receiving...
I am using nrf connect app on ios , the device is getitng on device mode but it is not showing DFU button on it , but it is working when using android app of it
And...
Dear all,
I am using SES, I have an application that relies on a softdevice. For it I developed a custom bootloader that DOES NOT rely on the softdevice and only transfers...
