Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Softdevice : S132
SDK ver : 15.3.0
Board : MBN52832DK
Hi There,
i was trying to do the DFU Example (ref : https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog...
Hi,
I am using nrf52840 dongle and tried to program it with the example that was provided with sdk15. I programmed it with ble_app_bps, it successfully paired with my...
Hi there,
I'm working on a BLE project using the nRF52832 and am having trouble implementing flash storage. I'm using SDK 132 v6.1.1, and the flash storage library to save...
I am implementing the Device Information Service, and want to include the bootloader version as "Firmware revision" in DIS and the application version as "Software revision...
I am new to nordic ble chips.
I am using nrf52832 ble chip, s132_nrf52_3.0.0_softdevice
I am trying to update firmware on the air. But I am getting an error that I do not...
Hey,
Up until now I have only been dealing with software. Now however, I want to create a device that I can use to track my bike by GPS and heading. In the future, I want...
Hi
I am having a problem now(maybe a bug).I refer to nest_state.c and access.c build my user_flash.
But some time,when I reset device,write data to flah will be fail....
Hi,
I'm using the nrf52840 with sdk v15.3 and I'm trying to list of the characteristics of a specific service that has a 128 bit uuid running on a peripheral. However, even...
Hello,
I would like to be clear on the pros/cons of registering a new SIG-adopted UUID versus a vendor-specific UUID. We are a small developer and the cost of registering...
Hello,
I have two differents sensors on one SPI port and I don't really know how to be able to use both. Of course all are connected in the same MISO/MOSI/SCK but there...
Hello,
We currently have several devices out in the field as test units, installed at beta sites. The new modem firmware v1.1 has several features/fixes that we want to...
Hi, we are working on custom board using nRF52811 SOC, I have some confusion
1. regarding the antenna design, I copied the Antenna from Dev board, but it is designed for...
Hello,
There's an interest on the LTE-MTC module.
I can see it's based on nRF9160.
I'd like to inquire about the MTC technology please, does this module support CATM2...
Hi,
I'm using a buffer size of 64 bytes using function
nrf_drv_uart_rx(&app_uart_inst, rx_buffer, 64);
When I receive only one byte packet from the remote, I get EVENT_RXDRDY...
i want to use pwm of rnf52810.but i don't know how to recognize what pins is pwm.
what pins in 52810 i can use wire to connect and then use it's pwm function?
or i can...
