Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, i am working on a bluetooth application with the nRF52832. When i try to connect a Samsung Galaxy S8 (Android 8.0) via nRF Connect, i get a LMP TIMEOUT error after 40...
Launch, then select 'Launch Programmer, tool displays message "The app only supports nRF connect ^2.5.0 while your installed version is 3.0.0. It might not work as expected...
From what I could see the Asset_Tracker example works in LTE, not in NB-IoT. How can I test NB-IoT?
I would like to get some hint on what example to use and what to do to...
Hey all,
I'm a bit lost here... I developed a wireless sensor for a customer based on the nRF52840 and it works great. Now we're developing a small light weight gateway...
Hi everyone,
I'm trying to developp a MIDI USB class compliant device with the nrf52840 DK.
I'm beginner about USB developpement and I have only basics about MIDI class...
I am using SDK 15.3.0 working on nRF52832, on windows platform.
Our requirement is, we need to get the data from both nRF52832 and BLE Heart rate sensor at same time and...
I have developed a new board based around NRF91 module. Ten prototypes are produced and six of them work. Other four devices cannot connect to the LTE network. I am using...
Hi,
I'm using nrf_serial to configure and then read data from a GPS engine, but I am getting unrecoverable OVERRUN errors on start-up if the GPS device is sending data when...
Hello
the setup is a nrf52840, the sdk15.3, Softdevice s140, apps: open bootloader and blinky app
Is there a way that the DFU mode is always there, at the moment its only...
Hi,
We are in the HW verification stage of a product with an nRF52 series MCU. We were easily able to measure the 32MHz XTAL accuracy using the buffered output feature;...
Hello, Dear Support!
From the DevZone I downloaded ntf5-multilink-example-master. Here . Thanks for developers. The solution in SES was built and uploaded without any troubles...
I am using 'Segger Embedded Studio'. While changing the settings of a project in options, why we select Private Configurations (common)? I have seen this procedure in many...
Hi,I had a new project base on nRF52810. I watnted to created a timer, but the note mentioned " increase the value of the macro APP_TIMER_MAX_TIMERS by one ".I couldn't find...
Hi,
is nRF9160 SiP comes with eSIM? or do I need to insert external SIM in socket which is traditional method?
Do I need to external chip antenna? does that antenna...
Hi:
Because our project using much nRF pin resources, we have to use the defualt function NFC pins (P0.09 and P0.10).we want to set these two pins as uart function ,but...
