to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
hi, i want to update firmware by OTA from sdk11.0.0_89a8197 to SDK_15.2, but can not scucess.
i tried follow command to build a zip file.
nrfutil pkg generate --hw-version...
Hello,
Here's my current setup:
I am using the nrf52840 SoC for development, which as I understand, has 2 UART instances available. One instance is being used for a third...
Hi
i am using the nrf52832 dk.
I am trying to combine the ble_app_uart code along with the fds code using ses.
what are the changes i have to make in the config file...
I changed the I2C pins to below, and it not work. so is it possible to reconfigure the I2C pin? what should I do since I already set to 8&9 in the hardware board? const nrf_drv_twi_config_t...
Hi,
Looking for some ground on getting the netowork parameters set for a zigbee device, My intention is to limit the number of scan intervals and the scan time to save power...
I'm planning wireless conference system. This needs some condition as under simultaneously use 5ch of wireless bi-directional connection through whole system. Each wireless...
Hi,
I am using nRF52832 soc to develop my project. with nRF5_SDK_15.3 . SES file
I need to connect both BMI160 accelerometer sensor and AT24C512 EEPROM ic in TWI.
how...
I am trying to update firmware that uses v14 of the nRF5 SDK to firmware that uses v15.3, but I am getting the error "Init command larger than expected.".
I'm wondering...
Hello everyone,
I'm running the IoT CoAP example on my nrf52840 Development Kit.
The border router is Rapberry 3 B+ on Jessie with Kernel version 4.19.46. I've put BLE_6LOWPAN_LEGACY_MODE...
I am using nRF5SDKforThreadandZigbeev300d310e7 sdk for thread example simple_coap_client. I try to add uart module with simple_coap_client and i have added uart configuration...
Hi,
I am running nrf52840 on a custom board, SDK 15.0.0, softdevice S140 6.0.0 and SES.
In my application I am reading an IMU ( ICM20602) and a laser ranger/Time of Flight...
hi,master.
Question 1: In Asia, the speed of accessing web pages is slow. SDK15 development documents can only be accessed online on the official website, but often cannot...
Hi,
I am running NRF52840 on a custom board with SDK 15.0.0, Softdevice S140 6.0.0 and SES.
I am measuring using a toggled GPIO pin measured on a CRO. This produces a...
I'm using an nRF52DK to monitor the RSSI and MAC address of my two phones through ble_evt_handler BLE_GAP_EVT_SCAN_REQ_REPORT.
I tested both Android and iPhone. They both...
