I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hi, I am using the following setup: Wireshark 2.6.5 (updated yesterday) Sniffer 2.0.0-beta-3 (nrfsniffer200beta312oct20181c2a221.zip) nRF52840-DK (used by the sniffer) nRF52840...
I have a custom board that uses Nordic NRF52832 as MCU. For laying out crystals, BLE part and decoupling capacitors, I used reference layout from documentation.
32 MHz crystal...
Hi everyone,
My hw/sw configuration:
- nRF52840 - sdk 15.0.0 - softdevice: s140_nrf52_6.0.0
I would like to change the device name and update it in advertising packet...
Hi All,
I have been working on ipv6 over ble on zephyr RTOS to form mesh network.I have been successfully integrated "rpl_node"(which is in zephyr/samples/net/rpl_node)...
Hi guys,
I have very strange problem with the Android phone when connect with nrf51822.
After connection, I used update parameters to set the parameters on the phone side...
Hello,
I am attempting to program nRF52 DK modules to communicate using the UART over BLE central and peripheral roles as in the examples provided in SDK 15.2. The data...
hello, I have used NRF52810 TWIM for 24LC08 communication, and I got a problem.
when I want to read data from 24LC08, if the length is not lager than 255, every thing is...
Dear all,
Good morning,
We are using nrf52832 as our main mcu. Our current consumption in system-off mode in custom board is around 3.2 mA which is very high and we want...
HI devzone
We now use NRF52832 to implement TDMA protocol.
In our application, there is one primary node and six sub-nodes.The communication process is as follows:
After...
I want to add simple on off switch model via SDK 2.2.0.
I'm already add client model to project,when provisioner add client node,Provisioner RTT jump error opcode status...
Hello Everyone,
Maybe this is a very silly question.
I am trying to implement timer in nrf51822 with S130, SDK11.
Code snippet:
void TIMER1_IRQHandler(void)
...
Hi,
i Have two development kits where one acts as uart central and another acts as uart peripheral .
In that i have given the peripherals different names( DEVICE_NAME...
Hi, I would like to ask how can i get the current consumption that was stated in the datasheet which is 0.7uA and the value I get from the reading is about 8-9 uA.
Is...
Hi team,
I am using sdk 14.2 ,nrf52840 DK board.
I am getting the following error while running nrf5-mpu-ble-simple code in keil. <error> app: Error 0x000D (13) at line...
hi.....
i am using nrf52832 ........
i want to wake up my device from sleep mode ... i have used the command for sleep mode sd_app_evt_wait() ...... i dono what command...
