Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
Hi folks,
I have been successful in getting sample code compiled using Keil u-vision and MBED and installing it on nrfDK-51. It has become so simple to install apps - all...
Hi everyone,
I successfully compiled and loaded the experimental_ble_app_uart onto my pca10028 board.
I downloaded and installed the nRF toolbox on my nexus 7 tablet....
Hello everybody,
I want to do something very simple: Read some data from my Bluetooth peripheral. I know the UUID of the data I want to read, but I do not know the handle...
Hmm... this should be a simple question. But I haven't found a direct answer yet in the online SDK docs, the ARM NVIC docs, nor in this forum (and have only been confused...
Hi All,
I have a following setup :
The peripheral BLE device is supposed to send **(time critical )**data packets to Central device but the transfer is very rare (Can...
Hi,
I have modified slightly the OTA bootloader sample in SDK6.1 and SoftDevice 7.1.0. After flashing the bootloader code to the nrf51822 it works like charm, I can update...
when i use BLE_GAP_ADV_TYPE_ADV_DIRECT_IND mode,I can see the device advertise (MCP) but i couldn't able to connect with it (advertising_start at BLE_GAP_EVT_TIMEOUT)
i...
Hi,
I'm a beginner with bluetooth.
I'm actually working with nrf 51822 Evaluation board.
I want to realize a transparent mode of communication with your kit. Can you...
I never worked with Cortex M0 before so I wonder how it's possible to jump to correct IRQ handler when I have my own bootloader and application which are using e.g. UART IRQ...
Hi.
Where i can find some information and guidelines to do a good RF PCB with nrf51822?
thank you for your support
EDIT 02/02/2015
Where i can find " nRF51822 Reference...
Hi, I'm using my custom board with NordicSemi nRF51822-QFAA and J-Link.
(Softdevice S110 7.1, SDK 7.2, and using IAR for ARM 7.1)
I was testing the NUS example using...
Hi,
The examples provided seem to indicate that the NRF51822 needs to be attached to an application processor / CPU (e.g. - Raspberry Pi). How much resources (CPU cycles...
hardware:pca1001
software:s120 v2.0.0 sdk 6.1.0
i will get rssi value by connected by s120.so i update the s120 to v2.0.0. but when the app run, an error occur.[APPL...
Hello,
I am using the Sd130 (v0.9 alpha-1) and do experience a reboot with NRF_ERROR_INVALID_STATE.
I start advertising, then use another device to connect to it. After...
